Find the polynomial by any suitable method

Assignment Help Mechanical Engineering
Reference no: EM13710267

A fourth-order polynomial passes through the five points for which the independent and dependent variables, x and y, respectfully, are given (-2,37), (-1,7), (0,5),(1,13), and (2,61). Find the polynomial by any suitable method. Here, x represents the spatial location and y the species concentration in chemical reactor.

Reference no: EM13710267

Questions Cloud

Two-dimensional steady-state heat conduction : Using Finite Difference and Finite Element to Solve for Two-Dimensional Steady-State Heat Conduction. Temperature distribution in the block (provide color contour diagrams) Temperature distribution along the top surface (present T vs x graphs)
Tubular body for high-pressure coolant and a carbide tip : What drill has one set of flutes that are ground to more than one diameter? What drill category includes more than one set of flutes allowing multiple diameters? What drill type incorporates a tubular body for high-pressure coolant and a carbide tip?
Refrigeration cycle operating : A refrigeration cycle operating between two reservoirs receives energy QC from a cold reservoir at TC = 280 K and rejects energy QH to a hot reservoir TH = 330 K. For each of the following cases determine whether the cycle operates reversibly, irreve..
Refrigerant enters the condenser of residential heat pump : Refrigerant-134a enters the condenser of a residential heat pump at 900 kPa and 40°C at a rate of 0.02 kg/s and leaves at 900 kPa as a saturated liquid. If the compressor consumes 1.2kW of power, determine (a) the COP of the heat pump and (b) the rat..
Find the polynomial by any suitable method : A fourth-order polynomial passes through the five points for which the independent and dependent variables, x and y, respectfully, are given (-2,37), (-1,7), (0,5),(1,13), and (2,61). Find the polynomial by any suitable method. Here, x represents the..
What is the controlling resistance for this heat transfer : A spherical container of outer diameter 2.5 m is buried below the wrath’s surface. The distance of the center of the container to the earth surface is 10 m. The container issued to temporarily store radioactive wastes where heat is generated at a rat..
Determine the rate of heat absorption from the outside air : Refrigerant-134a enters the condenser of a residential heat pump at 900 kPa and 40°C at a rate of 0.02 kg/s and leaves at 900 kPa as a saturated liquid. If the compressor consumes 1.2kW of power, determine (a) the COP of the heat pump and (b) the ra..
Estimate the range flaw sizes : A silicon nitride turbine rotor fractures at a stress level of 265 MPa. Estimate the range flaw sizes that could have been responsible for this failure.
Living plant leaf is an open system that exchanges energy : A living plant leaf is an open system that exchanges energy (sunlight and thermal flows) + matter (O2, CO2, water vapor, etc.) with the surroundings (the exterior). Even with irreversible processes (energy dissipation) we find that the net entropy ch..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Object depends on the dimensionless drag coefficient

The drag force on an object depends on the dimensionless drag coefficient, the density of air, the object velocity, and the frontal area of the object. By only considering units obtain a relation for the drag force.

  Consider the one-dimensional flow whose velocity is given

consider the one-dimensional flow whose velocity is given by u x t i. a determine the unsteady convective and total

  A steel plate is to be attached to a support with three

a steel plate is to be attached to a support with three bolts. the plate is 50 mm wide and 11.2 mm thick and the yield

  Design value for the molded friction material and steel disk

Design value for the molded friction material and steel disks to be used 0.06 and pressure max=1400kpa. Determine appropriate values for the disk inside dimmeter, the total number of disks and the actuating force?

  Determine the mach number of this plane for the stated limit

Determine the Mach number of this plane for the stated limiting condition.

  Determine the angular velocity theta dot of the combined

a wad of clay mass m1 with an initial horizontal velocity v1 hits and adheres to the massless rigid bar which supports

  Determine the final temperature of the ammonia

Ammonia vapor in a piston-cylinder assembly undergoes a constant-pressure process from saturated vapor at 10 bars. The work is +16.5kJ/kg. Changes in kinetic and potential energy are negligible. Determine (a) the final temperature of the ammonia in d..

  Derive the transfer function of this system with a

for a first order system with a transfer function of 15s2 given a unit step input pleasea. derive the transfer function

  Design a pump that delivers 200 litersmin at a pressure of

design a pump that delivers 200 litersmin at a pressure of 120 bar. the given data discharge and pressure can fit with

  A convective heat transer coefficient equal to 210 w m2-k

in a planned experiment a thermocouple is to be exposed to a step change in temperature. the response characteristics

  What will be the static water pressure in pound per square

based solely on available static pressure at a fire hydrant of 51.67 psi that has an elevation of 657 feet above see

  Show the cycle on a t-s diagram with respect to the

consider a 210mw steam power plant that operates on a simple rankine cycle. steam enters the turbine at 10mpa and 500oc

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd