Determine the rate of heat absorption from the outside air

Assignment Help Mechanical Engineering
Reference no: EM13710265

Refrigerant-134a enters the condenser of a residential heat pump at 900 kPa and 40°C at a rate of 0.02 kg/s and leaves at 900 kPa as a saturated liquid. If the compressor consumes 1.2kW of power, determine (a) the COP of the heat pump and (b) the rate of heat absorption from the outside air

Reference no: EM13710265

Questions Cloud

Refrigeration cycle operating : A refrigeration cycle operating between two reservoirs receives energy QC from a cold reservoir at TC = 280 K and rejects energy QH to a hot reservoir TH = 330 K. For each of the following cases determine whether the cycle operates reversibly, irreve..
Refrigerant enters the condenser of residential heat pump : Refrigerant-134a enters the condenser of a residential heat pump at 900 kPa and 40°C at a rate of 0.02 kg/s and leaves at 900 kPa as a saturated liquid. If the compressor consumes 1.2kW of power, determine (a) the COP of the heat pump and (b) the rat..
Find the polynomial by any suitable method : A fourth-order polynomial passes through the five points for which the independent and dependent variables, x and y, respectfully, are given (-2,37), (-1,7), (0,5),(1,13), and (2,61). Find the polynomial by any suitable method. Here, x represents the..
What is the controlling resistance for this heat transfer : A spherical container of outer diameter 2.5 m is buried below the wrath’s surface. The distance of the center of the container to the earth surface is 10 m. The container issued to temporarily store radioactive wastes where heat is generated at a rat..
Determine the rate of heat absorption from the outside air : Refrigerant-134a enters the condenser of a residential heat pump at 900 kPa and 40°C at a rate of 0.02 kg/s and leaves at 900 kPa as a saturated liquid. If the compressor consumes 1.2kW of power, determine (a) the COP of the heat pump and (b) the ra..
Estimate the range flaw sizes : A silicon nitride turbine rotor fractures at a stress level of 265 MPa. Estimate the range flaw sizes that could have been responsible for this failure.
Living plant leaf is an open system that exchanges energy : A living plant leaf is an open system that exchanges energy (sunlight and thermal flows) + matter (O2, CO2, water vapor, etc.) with the surroundings (the exterior). Even with irreversible processes (energy dissipation) we find that the net entropy ch..
Explain why an electric refrigerator : Explain why an electric refrigerator, which transfers energy by means of heat from the cold food storage compartment to the warmer air in the room, is not an impossible "clauses device."
Draw a diagram of the essential features of optical encoder : Explain the principle of operation of an AB encoder and how this is used to read an optical encoder. Draw a diagram of the essential features of an optical encoder.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The allowable shearing stress is 15ksi in a steel rod ab

the allowable shearing stress is 15ksi in a steel rod ab and 8ksi in a brass rod bc. knowing that a torque of magnitude

  Estimate the maximum elongation and maximum tensile stress

a 5-ton elevator is supported by a standard steel cable of 25 in2 cross section and an effective modulus of elasticity

  Calculate the pipe diameter

Calculate the pipe diameter D in inches to 2 decimal places required to give the fluid velocity of 4 ft/sec in the following situation: The formula for the velocity is given by: velocity =Flow rate / Pipe Area And the flow rate = 21 gpm and the Pipe ..

  If the temperature of the inner and outer surfaces of the

heat is transferred steadily to boiling water in a pan through its flat bottom at a rate of 650 w. if the temperature

  What is the percent span for the old and new setpoints

a reactor setpoint wasincreased from 160 psig to 190 psig. the reactor pressure transmitter was recalibrated from 0-200 psig to 0-300 psig. what is the percent span for the old and new setpoints?

  A 2 cm horizontal jet of water with a velocity of 15 ms is

a 2 cm horizontal jet of water with a velocity of 15 ms is spraying onto a vertical plate attached to a cart moving

  Manufacturer claims the average velocity of air leaving fan

A fan with a diameter of 12 inches operates at a voltage of 120V with a current draw of 0.5 amps. The manufacturer claims the average velocity of air leaving the fan is 33.1 ft./s under standard conditions. Standard air has a density of 0.075 lb mass..

  The sliding distance after the first 05 seconds g if the

it takes 0.5 seconds for one to lift the cart handle from 0 to 450 in a linear way around o. if the block has a mass of

  Calculate the magnitude of the moment

Calculate the magnitude of the moment about the base point O of the 600 N force and calculate and draw the shear force and bending moment diagram for the cantilever beam

  The virial equation of state for n-butane at 460k is

the virial equation of state for n-butane at 460k is z1avbv2 in which a -265 cm3g and b 30250 cm6gmole2. calculate the

  10 mols of liquid benzene at 20degc and 1 bar is pumped to

10 mols of liquid benzene at 20degc and 1 bar is pumped to 5 bar. at the inlet conditions the molar volume of benzene

  Determine the maximum load that can be carried by the

a tensile member of aluminum alloy 2024 - 0 had an original cross - sectional area of 4. 0 square inches. if the strain

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd