Find the operating points (q) for one pump

Assignment Help Civil Engineering
Reference no: EM13545638

The pump curve for a given pump is represented by hp,pump=20 (1-(Q/100)^2) where hp,pump is the head provided by the pump in feet and Q is the discharge in gpm. The system curve for a pumping application is hp,sys=5+0.002Q^2 where hp,sys is the head in feet required to operate the system and Q is the discharge in gmp. Find the operating points (Q) for

A.) one pump

B.) two identical pumps connected in series , and

C.) two identical pumps connected in parallel

Reference no: EM13545638

Questions Cloud

Determine the cop of the heat pump and rate : Refrigerant 134a enters the condenser of a residential heat pump at 800 kPa and 35 degrees celcius at a rate of 0.018 kg/s and leaves at 800 kPa as a saturated liquid. If the compressor consumes 1.2 kW of power, determine a) the COP of the heat pump ..
What contour intervals will be drawn if a 50ft interval : An area that varies in elevation from 463ft - 634ft is being mapped. What contour intervals will be drawn if a 50ft interval is used? Which lines are emphasized?
The mass center of the unbalanced disk of weight w is locate : The mass center of the unbalanced disk of weight W is located at G, which is a distance of R/2 from the center for the disk. In the equilibrium postition
What will be the discharge through the pipe : A pump having the characteristics given in figure 14.9 ( N=2133.5 rpm, n=35.6 rps, D=37.1 cm) pumps water at 25 degree C from a reservoir at an elevation of 366 m to a reservoir at an elevation
Find the operating points (q) for one pump : The pump curve for a given pump is represented by hp,pump=20 (1-(Q/100)^2) where hp,pump is the head provided by the pump in feet and Q is the discharge in gpm.
What is the minimum radius that can be cleared : A two lane hwy with 12' lanes is to be reconstructed to a design speed of 50 mph. Due to right of way restrictions, the largest distance that can be cleared from the edge of the road is 10'. What is the min. radius?
What is the tensile force on the weld per foot : Due to a leak in Pump Station 1,the Alaska pipeline is shut down briefly.The pipe line is half full.Assume the pipe is welded horizontally at its midpoint.What is the tensile force on the weld per foot? Assume Ø=40”and ?oil=53.55lb/ft3.
The average return period of the median value : The probability that, for a 2-year period, the peak flow rate will equal or exceed the median value in the second year, but not in the first year?
What happens after the memory is full : Assuming approximately 19,296 data points can be held in memory, with a 21X Datalogger (CR23X Micrologger), capturing battery voltage; panel temperature

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the optimal distance between the two drainage canals

To avoid the salinization of soil in a farming area, parallel drainage canals are to be installed to maintain the water table at a depth of at least 4m below the ground surface. It is thought that no evapo-transpiration would occur below that dept..

  Determine what is the runoff rate into the inlet grate

A paved parking lot section has a uniform slope over a length of 100 m (in the flow direction) from the point of a drainage area divide to the inlet grate, which extends across the lot width of 30 m.

  Determine what is the decrease in diameter d

A bar of monel metal (length L=9 in., diameter d=0.225 in.) is loaded axially by a tensile force P. If the bar elongates by 0.0195 in., what is the decrease in diameter d What is the magnitude of the load P

  What does chebyshes theorem tell us about the probability

over the range of cylindrical parts manufactured on a computer-controlled lathe, the standard deviation of the diameters is 0.002 millimeter/ (a) what does Chebyshe's theorem tell us about the probability

  Calculate max tensile force that the cable can withstand

A cable is made of two strands of different materials, A and B, and cross sections as follows: For material A, K = 60, 000 psi, n = 0.6, Ao = 0.6 in2 For material B, K = 30, 000 psi, n = 0.5, Ao = 0.3 in2

  Determine the moment about o of the resultant force exerted

Knowing that portion AC of the rope lies in a plane parallel to the xy plane and that the magnitude of the tension T in the rope is 62 lb, determine the moment about O of the resultant force exerted on the pulley by the rope.

  What is the vapor pressure of carbon dioxide in the bottle

What is the vapor pressure of carbon dioxide in the bottle before it is opened (i.e., when it is at equilibrium) assuming no other ions are present besides those related to CO2 and water

  Component of the force fac along the axis of strut

Determine the projected component of the force fac along the axis of strut ao. Express the result as a cartesian vector.

  What are the important findings

What are the important findings in Austin Road Co. v. OSHRC and Builders Steel Co. v. Marshall? Your response should be approximately 200 - 300 words and include a reference citation for your response.

  Calculate the diameter of this pipe

Using the Hazen-Williams approach (seecoefficient table below), find the headloss of water flowingthrough 1,000-ft of 6-ft diameter concrete pipe at a flow rate (Q)of 80 ft3/sec

  Which would mean that an embankment is in saturated

Total stress analysis is usually preferred for construction of embankments and for excavations, we use effective stress analysis, but why? Total stress is Undrained strength of the soil

  Determine the magnitude and coordinate direction angles

If the coordinate direction angles for F3 are a=120degrees, b=45degrees, y=60degrees, determine the magnitude and coordinate direction angles of the resultant force acting on the eyebolt.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd