Find the final temperature

Assignment Help Civil Engineering
Reference no: EM13559367

1.A horizontal water jet impinges against a vertical flat plate at 25 ft/s and splashes off the sides in the vertical plane. If a horizontal force of 350 lbf is required to hold the plate against the water stream, determine the volume flow rate of the water.

2.A piston cylinder contains 0.8kg of steam (water vapor) at 300 deg C and 1MPa absolute. The steam is cooled at constant pressure until half of the mass condenses.

(a) find the final temperature. (b) compute the volume change. (c) how many molecules of H20 is our system?

Reference no: EM13559367

Questions Cloud

Calculate and display the time it will take to travel from : Transportation need to evaluate the time spent in traveling from city A to city B. The distance between the two cities is a variable because the macro developed is to be used for other cities. 50% of travel time is done at a speed of 30 miles an
Verify that sample mean and the sample variance converge : Write a computer program that generates a sequence of random variables from a normal distribution with mean 5 and standard deviation 2.
What is the final pressure in the device : A .2kg mass of argon gas fills a .05m^3 piston-cylinder volume at a pressure of 400 kPa absolute. The piston induced pressure is changed until the volume expands to twice its original value, while the temperature remains constant.
What is the velocity of the water at the exit for maximum : A suction device is being designed based on the Venturi principle to life objects in submerged water. The operating water temperature is 50C. The suction cup is located 1.3 m below the water surface, and the Venturi throat is located
Find the final temperature : A horizontal water jet impinges against a vertical flat plate at 25 ft/s and splashes off the sides in the vertical plane. If a horizontal force of 350 lbf is required to hold the plate against the water stream, determine the volume flow rate of the ..
Determine the maximum horizontal distance that a projectile : Determine the maximum horizontal distance that a projectile will have at a height of 60 m above the orgin if it is fired at an angle at 70 degrees from the horizontal with a velocity of 50 m/s
The plus sight and minus sight distances were kept approx : A differential leveling loop began and closed on BM bridge (elevation 103.895m). The plus sight and minus sight distances were kept approximately equal
How many extractions are required to decrease : Phenol is approximately 12 times more soluble in 1 volume of isopropyl ether than it is in 1 volume of water. How many extractions are required to decrease the concentration of phenol below 100 mg/L
What mass of pac must be placed in a contact basin : Toluene has contaminated a city's drinking-water supply. An activated carbon system has been constructed so toluene concentrations are treated to below specified regulatory levels. If the toluene concentration in the water supply is 1,000 ppb

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the horizontal distance the shot travels

The angle of the release is 30 degrees. Determine the horizontal distance the shot travels from the point of release to the point where it hits the ground.

  Determine the number of truck loads required to obtain

For construction of an embankment, the soil is transported from a borrowed area using a truck which carries 5.5 m^3 of soil at a time, with the following details: For the Borrowed Pit: bulk unit weight= 16 KN/m^3 and moisture content = 6.7%

  Estimate settlement of footing four years after construction

The modulus of elasticity of the sand was determined to be 10,000 kN/m^3 throughout. Using the Schmertmann's method, estimate the settlement of the footing four years after construction, using four 1 meter thick sublayers.

  Determine the reaction of each of each of the six wheels

A trailer weighing 2400 pounds is attached to a 2900 lb by a ball and socket truck hitch at d. (A) Determine the reaction of each of each of the six wheels when the truck and the trailer is at rest. (B) and the additional load on each of the truck wh..

  What is the min possible value for the pressure difference

Part of a vertical piping system consists of 8 ft of 4 in diameter, connected to 8 ft of 3 in diameter above, and connected to 8 ft of 2 in diameter above that. Water at 60 F flows up the pipe (no downward flow occurs).

  Find length and width of square basin for virus disinfection

Find the length and width of a square basin for virus disinfection of a flow of 6 MGD. You may assume a depth of 5 ft, a C•t product of 10 (mg/L) •min for 1.5-log removal, and a target free chlorine residual of 0.6 mg/L.

  Identify the minimum and maximum deflection and rope tension

Friction of the walker's shoes and rope are sufficient to cause the rope to have more tension on one side then the other. Neglecting the weight and any elastic deformations of the 20.1-m long rope, create a table using 1.0m increment for the range

  Sketch the cycle on p-v coordinates

A quality of water within a piston-cylinder assembly executes a Carnot power cycle. During isothermal expansion, the water is heated from saturated liquid at 50 bar until it is a saturated vapor. The vapor then expands adiabatically to a pressure ..

  Calculate what is the flow rate of water over a length

The pressure drop in a 10 cm galvanized iron horizontal pipe (ks=.15mm) carrying water over a length of 50 m is 30 kPa. What is the flow rate

  Determine what was the velocity of a just before impact

All four of B's wheels were locked and skid marks indicate that B slid 2 m after impact. If you estimate the coefficient of kinetic friction between B's tires and the road to be 0.4 and the coefficient of restitution to be 0.4

  How to achieve a flow rate of 1 cfs at an elevation

Size an orifice and a weir for problem 2 on page 398 and 399 of the text book to achieve a flow rate of 1 cfs at an elevation of 102.5 feet and a total flow rate of 50 cfs at an elevation of 106 feet

  Determine the tension in each of the cables at a time when

A long trough is supported by a hinge along its lower edge and a series of horizontal cables attached to its upper edge. Determine the tension in each of the cables, at a time when the trough is full of water.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd