Find the downstream depth and the head loss in the jump

Assignment Help Civil Engineering
Reference no: EM13313440

a hydraulic jump is to be formed in a trapezoidal channel with a base width of 20ft and a side slope of 2:1. The upstream depth is 1.25ft and Q=1000 cfs. Find the downstream depth and the head loss in the jump.

Reference no: EM13313440

Questions Cloud

Determine water level rise in an unconfined aquifer produced : Determine the water level rise in an unconfined aquifer produced by a seasonal precipitation of four inches. The aquifers porosity is 20 percent and its specific retention is 9 percent.
How long does it take for platform to make one revolution : A spring scale on a rotating platform indicates that the horizontal force on a 0.606 kg mass is 1.57 N, How long does it take for the platform to make one revolution
Determine what is the void ratio of the soil : In its natural state, a moist soil has a volume of 0.33 ft3 and weighs 42.55 lb. The oven-dried weigth of the soil is 35.56 lb. If Gs = 2.63, what is the void ratio of the soil
Find the banking angle : A velodrome track is banked so that a bicycle traveling at 62.8 km/h will have no tendency to slip to either side when traveling on the path that has a radius of curvature of 79.0 m
Find the downstream depth and the head loss in the jump : a hydraulic jump is to be formed in a trapezoidal channel with a base width of 20ft and a side slope of 2:1. The upstream depth is 1.25ft and Q=1000 cfs. Find the downstream depth and the head loss in the jump.
What is the radius of the wheel : During 0.15 s, a wheel rotates through an angle of 2.74 rad as a point on the periphery of the wheel moves with a constant speed of 2.16 m/s
Calculate what is the standard error of the observations : You measure an angle with a theodolite several times and record the following observations. What is your best estimate of the true value of the angle What is the standard error of the observations
What is your average speed for the entire trip : You drive on Interstate 10 from San Antonio to Houston, half the time at 63 km/h and the other half at 86 km/h. What is your average speed for the entire trip
Create effective teams using innovation : Create effective teams using innovation.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What flow rate of fresh water used to reduce concentrations

The new owners propose to flush the pond into their discharge pipe leading to the Atlantic Ocean, which has a salt concentration above 30,000 mg/L. What flow rate of fresh water (in m3/s) must they use to reduce the salt concentration

  Determine the new reading along the inclined leg

If the pressure in pipe B is decreased 10 kPa and the pressure in pipe A remains unchanged, determine the new reading along the inclined leg of the mercury manometer.

  Elastic modulus of steel

Given: elastic modulus of steel is 200 GPa, yield and ultimate tensile strength of steel are 600 and 750 MPa, respectively.

  How far apart must two 18 m diameter tanks be placed

How far apart must two 18 m diameter tanks be placed such that their stress overlap is not greater than 10% of the contact stress at depths of 10, 20, and 30 m

  Determine what does the equation reduce to in steady flow

Define what each term in the equation means. Overall, what quantity is being conserved? Under what conditions might you be justified in assuming that non-linear terms are not important

  Determine the value for cu and the cohesion intercept c

At failure, the respective minor and major principal stress values are 20 kPa and 46 kPa for one and 40 kPa and 80 kPa for sample two. From these data, determine the value for (phi)cu and the cohesion intercept c on the Mohr's circle shear stress ..

  Determine the magnitude of force p to produce

A thin-walled cylindrical tank of radius r is subjected simultaneously to internal pressure p and a compressive force P through rigid end plates. Determine the magnitude of force P to produce pure shear in the cylindrical wall.

  Calculate the wet unit weight in pounds per cubic feet

A gray silty clay (CL) is sampled from a depth of 12.5 feet. The "moist" soil was extruded ffrom a 6-inch high brass liner with an inside diameter of 2.83 inches and weighed 777 grams.

  How many days would need to use the equipment each year

How many days would they need to use the equipment each year to justify purchasing the equipment? To purchase equipmet/ Buy at $60,000, Operation and maintanence is $120/day, life is 5 yrs and salvage value is $5000.

  Tape corrections under following conditions

The tape is stretched over three equal spans. Calculate the tape corrections under the following conditions at field, temperature = 85ºF, pull = 18kg, E= 2.109 x 10 6 kg/cm 2

  Determine how much astronaut will weigh on the beam scale

An 80 kg astronaut took his bathroom scale (a spring scale) and a beam scale (compare masses) to the moon where the local gravity is g=1.67 m/s^2. Determine how much he will weigh

  Determine the maximum acceleration from rest

A rear-wheel-drive car 2600 lb, has an 80-inch wheelbase, a center of gravity 20 inches above the road surface and 30 inches behind the front axle, a drivetrain efficiency of 85%, 14-inch-radius wheels,

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd