Find method to compute the flexural stresses for the load

Assignment Help Civil Engineering
Reference no: EM13313765

Assume the section has cracked and use the transformed area method to compute their flexural stresses for the load. Given: Beam 30 ft long with uniform load of 2 k/ft and a point load of 30 k at 10 ft. Cross section b=16 in h=36 in with 6 #9 rebars located 32 in from the top. n=10

Reference no: EM13313765

Questions Cloud

Simplify the default set of sources : Extend the editing of vehicles to allow editing of the weight (importance) of a sensor in determining the motion of the vehicle.
What is the static pressure of the water at the outlet : A PVC pipe has an inside diameter of 40 mm, is 30 m long and carries 10°C water at a rate of 3.5 m3/hr. At this rate, the friction factor of the pipe is 0.0814.
Calculate weight percent austenite and weight proeutectoid : a .65% Carbon hypoeutectoid plain carbon steel is slowly cooled from 950 degrees C to just slighty above 723 degrees C calculate the weight percent austenite and weight proeutectoid ferrite in this steel
What was the speed of cue ball before and after collision : A cue ball, which has a mass of 0.17 kg, collides head on with a stationary 8 ball, what was the speed of the cue ball before and after collision
Find method to compute the flexural stresses for the load : Assume the section has cracked and use the transformed area method to compute their flexural stresses for the load. Given: Beam 30 ft long with uniform load of 2 k/ft and a point load of 30 k at 10 ft.
Compute the total tax they would pay as unmarried individual : John Adams has a $65,000 adjustable gross income from Apple Corp. and allowable itemized deductions of $7200. Mary Eve has a $75,000 adjustable gross income and $2000 of allowable itemized deductions.
Depict network topology graphical model initial environment : Depict a network topology graphical model of the initial environment of 10 employees using Visio or its open source alternative software. Note: The graphically depicted solution is not included in the required page length.
Find the lenght of electromagnetive waves : find the lenght of electromagnetive waves if end of frequency omega 10 in 5 hertz omega and absonant is 885 15 perimeter
Determined from the equilibrium data to be percent by mass : a mild steel component in a form of a finite slab with a thickness of 2L=2.5 mm is to be hardened by packing it in a carbonaceous material in a furnace for a predetermined time. the uniform initial carbon concentration of the slab is 0.15 percent ..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the quantity of heat transferred to the water

Water is used in a heat exchange to cool 5 kg/s of air from 400 C to 200 C. Calculate (a) the minimum mass flux (kg/s) of the water and (b) the quantity of heat transferred (MJ) to the water each second.

  What would be failure deviatoric stress sigma1-sigma3 stress

The effective angle of friction (phi) was found to be 26 degrees for a normally consolidated soil. If the soil is tested in consolidated drained triaxial test under sigma3 = 60 kPa, what would be the failure deviatoric stress sigma1-sigma3 stress

  What is effect of packing factor in self compacting concrete

what is effect of packing factor in self compacting concrete?

  Determine which equation is valid in any system units

According to information found in an old hydraulies book, the energy loss per unit weight of fluid flowing through a nozzle connected to a hose can be estimated by the formula h=(0.04 to 0.09)(D/d)^4*V^2/2*g

  Compose a list here of the geological terms

compose a list here of the geological terms that you encounter in this reading that you could not define and explain in a test situation.

  Calculate the required plate area and the number of plates

An Electrostatic Precipitator must treat 500,000 acfm with 99% efficiency. Assuming an effective drift velocity of 0.4 ft/sec, calculate the required plate area in ft^2, and the number of plates if each is 20 ft tall by 10 ft long, and there are 4..

  Determine the horizontal deflection of joint

The maximum vertical load and horizontal load have been identified and shown in the figure. Under this loading condition, you are asked to determine the horizontal deflection of joint C.

  Determine the speed with which b must walk toward a

Swimmer A immediately starts walking toward B at a speed of 2ft/s relative to the raft. Knowing that the raft weighs 300 lb, determine (a) the speed of the raft if B does not move, (b) the speed with which B must walk toward A

  Depict a decision tree

The mine's operating costs were projected at $900,000 per year including $400,000 of fixed costs and $500,000 of variable costs. Ms. Peru thought these forecasts accurate.

  Standard deviation in lines of levels

Lines of levels were run requiring n instrument setups. If the rod reading for each backsight and foresight has a standard deviation δ what is the standard deviation in each of the following level lines?

  Determine slenderness ratio l per r and euler buckling load

An aluminum alloy tube with an outside diameter of 2.9 in. and a wall thickness of 0.32 in. is used as a 19-ft-long column. Assume that E = 8300 ksi and that pinned connections are used at each end of the column.

  What should the removal efficiency of a process designed

Wastewater flow of 2000 m3/day containing 120g/L of salt. Discharge into a river with a flow of 34,000 m3/day and a salt concentration of 50 mg/l. The agency wants to maintain the salt level to no greater than 250 mg/L downstream of the discharge.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd