Estimate the pressure 200m downstream of the treatment plant

Assignment Help Civil Engineering
Reference no: EM13308435

water from a treatment plant is pumped into distribution system at a rate of 4.38 m^3/sec, a pressure of 480 kpa and a temperature of 20 degree celcius. The pipe has a diameter of 750 mm and is made of ductile iron. Estimate the pressure 200m downstream of the treatment plant if the pipe remains horizontal. Use the moody diagram to determine the friction factor ( you can also use the Swaimee-Jane equation). After 20 years in operation, scale buildup is expected to cause the roughness of the pipe to increase by a factor of 10. What is the effect of this on water pressure 200 m downstream of the plant? Say, Water flows at a velocity of 2m/sec in a 300 mm new ductile iron pipe. Estimate the headloss over 500m

Reference no: EM13308435

Questions Cloud

How i should write out the source file : Given struct vector scale_vector (struct vector v, double scalar) for the header file.
Discuss some useful applications for n-dimensional arrays : Discuss some useful applications for n-dimensional arrays, such as graphical 3-D or biotechnology applications.
Find dry unit weight-void ratio and degree of saturation : A soil specimen has a water content of 18% and a wet until weight of 118.5 lb/ft. The specific gravity of solids is found to be 2.72. Find the dry unit weight, void ratio, and degree of saturation.
Explain the format of the processor''s logical address : What is the format of the processor's logical address. What is the length and width of the page table (disregarding the "access rights" bits)
Estimate the pressure 200m downstream of the treatment plant : water from a treatment plant is pumped into distribution system at a rate of 4.38 m^3/sec, a pressure of 480 kpa and a temperature of 20 degree celcius. The pipe has a diameter of 750 mm and is made of ductile iron
Please make a positioning map for kraft yuban coffee : Please make a Positioning map for (Kraft) Yuban coffee without using price or quality as attributes. The competitors are JM Smucker, Nestle, Starbucks, Green Mountain and Sara Lee.
What should be the design capacity of the distribution pipes : A water supply system is being designed to serve a population of 200,000 people with an average per-capita demand of 600L/Person-day (peak demand factor is 1.8) and a needed fire flow of 28,000 L/min.
Determine what is the concentration in lake water with ph : What is the concentration (M) of Al3+ in lake water with pH = 4 assuming the equilibrium below with excess Al(OH)3 (s) The reaction is Al(OH)3 (s) --> Al3+ + 3OH-. pKsp = 32.9.
What is the use of win32 console functions : What is the use of Win32 Console functions and how they relate and pertain to GUI.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the free flow speed on specific westbound

On a specific westbound section opf highway, studies show that the speed density relationship is u=uf *[1-(k/kj)^3.5]. It is known that the capacity is 4200hehicle/hr and the jam density is 210 veh/mile.

  Compute the final temperature and pressure of the gas

A tank is divided into two equal chambers by an internal diaphragm. One chamber containes methane at a pressure of 500 bar and a temperature of 20 C, and the other chamber is evacuated.

  Construction of the embankment

Pore water pressure is to be observed during the construction of the embankment. Calculate the pore water pressure which must not be exceeded at any point in the clay layer 9 m below the surface of the embankment to ensure a shear strength of 100 ..

  Determine what is the work function for the metal

582 nm photons are used in a photoelectric experiment. An electron is just released from metal with little or no kinetic energy at this frequency. What is the work function for this metal

  Determine the total dead load

determine the total dead load, per foot of length, each beam must support.

  Find what design speed was used for freeway exit ramp

A freeway exit ramp has a single 12-foot lane and consists entirely of a curve with a central angle of 90 degrees and L=628 feet. If the distance cleared of obstacles is 19.4 feet from the centerline, what design speed was used

  How to find degree of kinematic indeterminacy

how to find degree of kinematic indeterminacy

  How many acres are within the enclosed by the fence

A contractor has installed a silt fence around an area that is semi-circular and level to prevent soil from the construction site entering nearby streams. The diameter of the semi-circle is 1000 feet.

  Draw the influence line for the support reaction

Draw the influence line for the support reaction at A and calculate the support reaction at point

  Describe what are the different dimensionless groups

What are the different dimensionless groups that describe a golf ball. A golf ball has two velocities, a spin velocity and a forward velocity.

  Explain how to describe the operation of series rl circuit

The discussion must address phase angle relationships of current and voltage. The answer must include the effect of source frequency on the voltage drops across the resistor and the inductor at very low and very high frequency values.

  Find the torsional moment t for the maxiumum shear stress

The pipe has an outside diameter of 60mm and an inside diameter of 50mm. Find the torsional moment T if the maxiumum shear stress is 80MPa.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd