Dynamic viscosity of the liquid between the plates

Assignment Help Civil Engineering
Reference no: EM13533379

1.The relative velocity of two infinitely wide parallel plates thatare 1cm apart is 10cm/s. If the dynamic viscosity of the liquid between the plates is 0.001 N s/m2 what is the shear stress between the plates?

2.Express each of the three forces acting on the bracket in Cartesian vector form with respect to the x and yaxes. Determine the magnitude and direction θ of F1 so that the resultant force is directed along the positive x'axis and has a magnitude of Fr = 600 N.

3.If φ = 45 degrees, F1 = 5kN, and the resultant force is 6kN dircted along the positive y axis, determine the required magnitude  of F2 and its direction θ.

Reference no: EM13533379

Questions Cloud

Calculate the inductance of the inductor in this circuit : A series RLC circuit consists of a 49-ohm resistor and a 5.0-uF capacitor. what is the inductance of the inductor in this circuit
Compute with what force should you pull with rope horizontal : You're using a rope to pull a sled at constant velocity across level snow,with coefficient of kinetic friction 0.050 between sled and the snow. With what force should you pull with the rope horizontal
What direction should the boat have been headed to actually : To cross a river that is 1 km wide, with a current of 6km/h, a novice boatskipper holds the bow of the boat perpindicularto the far river bank, intending to cross to a point directly across the river from the launch point.
How much settlement has occurred when the time factor is : If the final consolidation settlement is expected to be 1.0m, how much settlement has occurred when the time factor is 0.2 andwhen it is 0.7?
Dynamic viscosity of the liquid between the plates : The relative velocity of two infinitely wide parallel plates thatare 1cm apart is 10cm/s. If the dynamic viscosity of the liquid between the plates is 0.001 N s/m2 what is the shear stress between the plates?
Calculate the consolidation settlement expected : For the profile shown, the initial ground water table is 5 ft belowthe surface. A proposed dewatering project will cause the watertable to drop 10 ft from the original level. Consolidation tests performed on clay samples produced the following result..
Find the normal strains in these two directions : If the normal stresses in the x and y direction are given byσx and σy, find the normal strains in these two directions.
Determine the rate of evaporation of water : Water is to be boiledat sea level in a 30 cm diameter stainless steel pan on top of a3-kW electric burner. If60% of the heat generated by the burner is transferred to thewater during boiling, determinethe rate of evaporation of water.
Determine which is a better site for wind power generation : Two sites are being considered for wind power generation. In the first site, the wind blows steadily at 7 m/s for 3000 hours per year, whereas the second site the wind blows at 10m/s for 2000 hours per year

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the height from the ground and the time at which

Ball A is thrown vertically upward from the top of a30-m-high-building with initial velocity of 5m/s. At the same instant another ball B is thrown upward from the ground with aninitial velocity of 20m/s. Determine the height from the ground andthe ti..

  Find the amplitude-period-max velocity-max acceleration

A 20g mass vibrates accordings to the equation x=0.0009cis(3pit/2 + pi/2). Find the amplitude, period, max velocity, max acceleration, spring constant "K", and the total energy of the system

  Question 1 a what are minerals sketch different types of

question 1 a what are minerals? sketch different types of mineral crystal forms and list different types of rock

  How to estimate the time of submersion in years

Apiece of corroded steel plate was found in a submerged ocean vessel. it was estimated that the original area of the plate was 62.5cm 2 and approximately 2.8k had corroded away during the submersion.

  Determine the stationing and elevation of the pvcs and pvts

Two level sections of an east-west highway (G=0) are to be connected. Currently, the two sections of highway are separated by a 4000-ft (horizontal distance), 2% grade. The western most section of highway is the higher of the two and is at elevati..

  How to compute the year in which the gradient ends

the present worth of an increasing geometric gradient is $23,632. The interest rate is 10% per year, and the rate of change is 4% per year. If the cash flow amount in year 1 is $3000

  Determine what is the four lane freeways aadt

A four lane freeway (two lanes in each direction) operates at capacity during the peak hour. It has 11-ft lanes, 4-ft shoulders, and there are three ramps within three miles upstream of the segment midpoint and four ramps within three miles downst..

  Calculate the flow rate per unit width of the aquifer

In a water table aquifer bounded on the ends by rivers, the hydraulic conductivity is 50 m/day. The hydraulic heads at x = 0 and x = 1000 m are 100 m and 90 m, respectively.

  How to determine the scale reading at t

A large tank is used to calibrate the reading from a flow meter. Measurements of the system weight as a function of time are made. Water enters the tank vertically from the flow metering system at a speed of 20 ft/sec through a 1.5 in.

  Calculate what should the sample volume be

The dissolved oxygen of sample water is 1.5 mg/L. At 25 C, the dissolved oxygen of the dilution water is 8.25 mg/L. You are told the BOD5 of the sample is 130 mg/L. You have a target final dissolved oxygen of 3.0 mg/L

  What is the isentropic efficiency of the compressor

An adiabatic argon unit compresses argon at 200 kPa and 27C to 2.18 MPa. If the Argon leaves this compressor at 513C. What is the isentropic efficiency of the compressor

  Calculate the axial and radial strains and volumetric strain

A cylindrical soil, 75mm in diameter and 150 mm long, is radially compressed. The length increases to 153 mm and the radius decreases to 37.2 mm. Calculate: a) The axial and radial strains b) The volumetric strains

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd