User Account

All Pages

Driving a 2000-ft loaded horizontal conveyor at 4 fts

Assignment Help Mechanical Engineering
Reference no: EM13625421

Driving a 2000-ft loaded horizontal conveyor at 4 ft/s requires 35hp. What horsepower would be required if the conveyor is now raised at on end, giving a gradient of 1 ft of rise in 60 ft of horizontal run? Each foot of conveyor carries a load of 20 lb.

Reference no: EM13625421

Questions Cloud

Determine the minimum number of expansion joints required : a bridge to be fabricated of steel girders is designed to be 500 m long and 12 m wide at ambient temperature assumed 20
The following is the heart rate for 10 randomly selected : the following is the heart rate for 10 randomly selected patients on the unit. find the mean variance and standard
What is the absolute pressure at a point that is 770 cm : mercury is poured into a tall glass. ethyl alcohol which does not mix with mercury is then poured on top of the mercury
Which is that hardness is measured as the applied load : one of the inspectors in the quality control department has frequently used the brinell and rockwell hardness tests for
Driving a 2000-ft loaded horizontal conveyor at 4 fts : driving a 2000-ft loaded horizontal conveyor at 4 fts requires 35hp. what horsepower would be required if the conveyor
Wwhat is the anticipated load at which the speciment is : a bending test is used on an experimental cemented carbide material. based on previous testing of the material its
The flow curve for austenitic stainless steel has the : the flow curve for austenitic stainless steel has the following parameters strength coefficient 1200 mpa and
With the equipment provided in labs why do you observe only : with the equipment provided in labs why do you observe only the balmer series but not the lyman or paschen series?a the
A piping system consists of 100 ft of 2-in pipe a sudden : a piping system consists of 100 ft of 2-in pipe a sudden expansion to 3-in pipe and then 50 ft of 3-in pipe. water is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Estimate the safety factor with respect to infinite fatigue

a 20 mm diameter shaft with a 6 mm diameter transverse hole is made of cold-drawn steel having ultimate strength 550

  Determine the temperature of the air at the exit in ordmc

at steady state air at 200 kpa 52 ordmc and a mass flow rate of 0.5 kgs enters an insulated duct having differing inlet

  Ateam at 5 bar 320 c enters a steady state turbine with a

ateam at 5 bar 320 c enters a steady state turbine with a volumetric flow rate of 0.65m3s and evpands adiabatically to

  With u in fts and y in ft a do you think this equation

water flows near a flat surface and soe measurments of the water velocity u parallel to the surface at different

  What is comb drive actuator simulation steps in software

what is comb drive actuator simulation steps in ansys software?

  A rocket is launched through a thrust force of 7000000 lbf

1 a window of building loses 1.2 julessec of heat during 24 hours period time. determine heat loss during this in kj?2

  Why is the carnot cycle not suitable as an ideal cycle

why is the carnot cycle not suitable as an ideal cycle for all the power producing devices ?

  The maximum flow rate needs to be 0011 m3s pumps in the us

water at 10degc is pumped from a lake through a pipe to an elevation of 25 m above the lake surface. the pipe is 650 m

  If the volume of the air in the tank is 2 cubic meters find

an insulated rigid-wall tank contains air at 20 c and 2 bar. a paddle wheel located in the tank does work on the air in

  Calculate the thermal efficiency of the cycle and the net

consider an ideal steam regenerative cycle in which steam enters the turbine at 600 lbfin2 700 f and exhausts to the

  A stack t550 deg f and 750mm hg was sampled using epa

a stack t550 deg f and 750mm hg was sampled using epa method 5. the total gas volume that flowed through the dry gas

  Heat transfer coefficient between gas and each wire is 200

a thermocouple is placed in an exhaust pipe in a diesel engine. thermocouple is reading 500oc while the exhaust pipe is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd