Discuss the beneficial or detrimental effects

Assignment Help Civil Engineering
Reference no: EM131069747

Consider the engineering component with a stress concentration which is schematically sketched in Fig. 1.2. The component is subjected to variable amplitude fatigue which consists of constant amplitude stress cycles mixed with periodic overloads. The component is made of a high strength material and the extent of plastic deformation is small compared to the root radius of the notch in the component.

(a) Outline a procedure for the determination of the number of cycles to initiate and propagate the crack ahead of the stress concentration.

(b) Discuss the beneficial or detrimental effects of the overloads on the fatigue life

284_91a98640-812b-4c41-a528-136eb6d6a9f6.png

Reference no: EM131069747

Questions Cloud

Equation of the line that passes through : Write the equation of the line that passes through (1,1) and has the slope of 1 in point-slope form.
Explanation of the usefulness of the trial balance : Prepare the journal entries for the above transactions - Post them to the appropriate ledger accounts and calculate the cost of the machine to be included within the "Machine nominal ledger "
Psychological contract expectations of your boss : What are your psychological contract expectations of your boss and coworkers? Give examples of conflicts you have had at work, listing the expectation that was not met.
Find a hospital in your area : Go to www.jointcommission.org. Click on Quality Check and find a hospital in your area. View the accreditation quality report. Describe what you have learned about this hospital. How could health care consumers use this site in deciding where to s..
Discuss the beneficial or detrimental effects : Discuss the beneficial or detrimental effects of the overloads on the fatigue life
Next performance improvement project : Describe where this hospital needs the most improvement and why. Describe what you think the most important opportunity for improvement is. Recommend where to focus the next performance improvement project.
How does aging temperature affect the time and hardness : How does aging temperature affect the time and hardness? What happens to the 190°C (370°F) 3 and 10 minute specimens after one week? Why?
Distance of total crack growth under constant amplitude : The fatigue crack is propagated ahead of a stress concentration under a constant amplitude of imposed cyclic compressive loads. The cracks arrest naturally after advancing a distance of ten times the notch-tip radius. At this point, the notched sp..
Discuss the different types of advance directives : Discuss the different types of advance directives and the pros and cons of each. Do you have an advance directive? Has what you have learned this unit caused you to consider the need for one? Why or why not?

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine its velocity after it has traveled 10 meters

An offshore drilling rig is being towed out to sea. What is the maximum distance away that the navigation lights can still be seen by an observer standing at the shoreline? The observer's eye height is 5'8", and the uppermost navigation light is 130 ..

  Determine the compound empirical and molecular formula

A Silane contains 90.31 % silicon and 9.69 % hydrogen by mass. The compound has a molar mass of 62 g/mol. Determine the compound's empirical and molecular formula.

  What is the minimum possible value for this pressure

Part of a vertical piping system consists of 8 ft of 4 in diameter, connected to 8 ft of 3 in diameter above, and connected to 8 ft of 2 in diameter above that. Water at 60 F flows up the pipe (no downward flow occurs)

  Construct a v-t graph and an a-t graph at time interval t

A particle begins from s=0 and is traveling along a straight path at a velocity of v=(t^2-4t+3) m/s, where t is in seconds. Construct a v-t graph and an a-t graph at the time interval t=0 to t=4 s.

  What is the angular velocity of the carriers

If the outer ring rotates in the clockwise direction at 7 rpm and the inner ring rotates in the counterclockwise direction at 12 rpm, what is the angular velocity of the carriers and what is the velocity of C, the center of the top carrier.

  What should be the design q used in the full scale system

The flowrate (q) per unit lenght (ft^2/s) over the spillway shown below is a fuction of the upstream heah H, the acceleration due to gravity g, and the spillway height P.

  Calculate the angular displacement for the pulley d

The cylinder B is released from rest. Determine the speed of both masses (vA and vB) after B moves by h m. Also calculate the angular displacement for the pulley D. The diameter of the pulley D is 0.2 m. Neglect all friction.

  Determine the clearance between the tube and the cylinder

a 25-mm diameter steel cylinder 300-mm long falls, because of its own weight, at a uniform rate of 0.1 m/s inside a tube of slightly larger diameter. A castor-oil film of constant thickness is between the cylinder and the tube.

  Determine the change in its length and the change in its

The acrylic plastic rod is 200mm long and 15mm in diameter. If an axial load of 300N is applied to it, determine the change in its length and the change in its diameter. Ep = 2.70 GPa, Vp = 0.4.

  How many customers would be served pertruck if each home has

Making two runs per day, how many customers would be served pertruck if each home has once-per-week service and the truck is usedfive days per week?

  Determine the temperature at the final state

Also determine the temperature at the final state in part (b).

  What tensile force should be applied to the bar to maintain

Suppose that in an apparatus it is necessary to maintain precisely the cross section of a 20mm circular nickel steel bar. If this bar is heated to 200 deg Celcius

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd