Diameter pipeline from the boiler to the turbine

Assignment Help Mechanical Engineering
Reference no: EM13717420

In a steam power station, steam flows steadily through a 0.3 m diameter pipeline from the boiler to the turbine. In the boiler, the steam is at 5 MPa and 400 0 C while reaching the turbine it changes to 2 MPa and 3000 C. There is a loss of heat about 9 KJ/kg from the pipeline. Calculate the steam flow rate.

Reference no: EM13717420

Questions Cloud

Determine the specific work produced by the turbine : Steam flows through a turbine. The inlet stream is at 1200 KPa and 290 C. The pressure at the exit is 75 KPa. A) Determine the quality and temperature of the steam at the exit. B) Determine the specific work produced by the turbine.
What is the boiling heat transfer coefficient : Consider that you are boiling water near its critical heat flux in a pot on the stove without a lid (pressure is atmospheric). Suppose the hot burner has a surface temperature of 128 degrees Celsius. Assume a 1 square meter area. What is the boiling ..
Find gravitational potential energy of stone-earth system : A 0.31-kg stone is held 1.4 m above the top edge of water well and then dropped into it. The well has a depth of 4.8 m. what is the gravitational potential energy of the stone-Earth system when it reaches the bottom of the well
Air undergoes a polytrophic process in a piston cylinder : Air undergoes a polytrophic process in a piston cylinder assembly from p1=1 atm, T1=70 degrees F to p2=5 atm. Employing the ideal gas model with constant specific heats at 80 degrees F, determine the work and heat transfer per unit mass,
Diameter pipeline from the boiler to the turbine : In a steam power station, steam flows steadily through a 0.3 m diameter pipeline from the boiler to the turbine. In the boiler, the steam is at 5 MPa and 400 0 C while reaching the turbine it changes to 2 MPa and 3000 C. There is a loss of heat about..
Calculate the force which farmer needs to apply : A stubborn 110 kg pig sits down and refuses to move. Calculate the force which farmer needs to apply to budge the pig
Relative humidity and temperature of resultant air stream : Outside cool air at 15C and 40% relative humidity is mixed with inside air taken near the celling in a room at 32C and 70% relative humidity. Determine the relative humidity and temperature of the resultant air stream if the outside flow rate is 40 m..
What is the phase angle between voltage and current : Consider an RC circuit with R = 5600 Ohm, C = 1.70 x 10-6 F. The rms applied voltage is 120V at 60.0Hz. What is the phase angle between voltage and current
Evaluate what is the strength of the magnetic field : A metal rod 0.66m long moves with a speed of 2.3m/s perpendicular to a magnetic field. If the induced emf between the ends of the rod is 0.38V, what is the strength of the magnetic field

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd