Determine which waveform in each pair is lagging

Assignment Help Electrical Engineering
Reference no: EM13274328

Determine which waveform in each pair is lagging:

a) 6 cos(100πt-1000) and -6 sin (2π60t+1300)
b) cos(10t-1000) and - cos(t-1000)
c) cos (50πt - 1000) + cos (50πt - 200) and 9 cos (100πt - 200)

Reference no: EM13274328

Questions Cloud

What is the resulting overall voltage gain of cb amplifier : A CB amplifier is operating with R load = 10 kiloohms, Rc = 10 kiloohms, and R signal = 100 ohms. At what current Ic should the transistor be biased for the input resistance Rin to equal that of the signal source
Explain neutralize the acid and convert : If, in practice, 5.0 mL of 16.0 M nitric acid were added to effect the dissolution of the copper, what would be the minimum volume of 4.00 M NaOH required to neutralize the remaining acid and convert all of the Cu2+(aq) to Cu(OH)2(s)
Find his resultant displacement from camp : hiker starts at his camp and moves the following distances while exploring his surroundings: 75.0 m north, Find his resultant displacement from camp
Find the corresponding range of rout and g : An emitter follower is operating at a collector bias current of 0.25 mA and is used to connect a 10 kiloohm source to a 1 kiloohm load. If the nominal value of beta is 100, what output resistance Rout and overall voltage gain G result
Determine which waveform in each pair is lagging : Determine which waveform in each pair is lagging: a) 6 cos(100πt-1000) and -6 sin (2π60t+1300)b) cos(10t-1000) and - cos(t-1000) c) cos (50πt - 1000) + cos (50πt - 200) and 9 cos (100πt - 200)
What is the final temperature of the lemonade : A copper container of mass 0.300kg contains 2.0 kg of lemonade at 33degree Celsius. What is the final temperature of the lemonade
Derive binding or ionization energy which is equal to energy : the donor energy level is approximately 0.1 ev below the conduction band. the approximate value is calculated from the binding energy equation from hydrogen. derive the binding or ionization energy which is equal to the total energy.
Find the length of shorter of two sides of initial rectangle : A rectangle has an area of 33.66 cm2. When both the length and width of the rectangle are increased by 1.30 cm, find the length of the shorter of the two sides of the initial rectangle
Compute the mass of each product formed : Calculate the mass of each product formed when 244 g of silver sulfide reacts with excess hydrochloric acid. Ag2S(s) + HCl(aq) -------> AgCl(s) + H2S(g)

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Define the transmission line has an impedance

The transmission line has an impedance of 600 ohms and is terminated in a load of 600 ohms. The transmitter delivers an average power of 0.1 W to the input of the line.

  Determine the peak-to-peak output voltage-vpp

A certain sawtooth generator has the following parameter values: Vin: 3v, R: 4.7kohm, C:0.001uf. Determine its peak-to-peak output voltage if the period is 10 us. What is the Vpp

  Plot the modulation index necessary to keep the vdc constant

Write the mathlab program to plot the modulation index necessary to keep the Vdc constant at 1200v when the input power factor angle is varied from -60 degrees to 60 degrees.

  How much the meter movement has a series resistance

A meter movement has a series resistance of 10-ohm and a full scale current of 100mA. Use this meter movement to design a 10A full scale ammeter. Be sure to show a schematic of your design.

  What is the doping concentration in quasi neutral n and p

An ideal non-degenerate silicon step junction diode with an intrinsic level Ei exactly at mid band-gap is fabricated. Answer all questions related to this diode. a) If Vbi = 0.65V and NA=4ND, what is the doping concentration in the quasi neutral n ..

  Find nd on n side

Built-in voltage for a Si p-n junction is tested to be 0.6 V, NA = 2 X 10^15 cm^-3 on p side. Find ND on n side. (Assume ni = 1 x 10^10 cm^-3; and k*T/q= 0.026 V)

  Find line current and the power factor of the combined loads

Two three-phase loads are y-connected across a 300 Volt three phase line. One load draws 10kW at a p.f. of 0.9 leading, and the second load draws 8kW at a p.f. of 0.6 lagging. V(line-neutral)=300V/sqrt(3)=173.21V

  What value get for vswr s from voltage standing wave pattern

i) A table of values of the normalized magnitude of the voltage phasor on the line as a function of position on the line, with the normalization done relative to the value of the voltage magnitude at the voltage maximum point on the line.

  Find probability that integrated circuits are counterfeit

Box 1 contains 1000 Integrated Circuits of which 10% are counterfeit. Box 2 contains 2000 Integrated Circuits of which 5% are counterfeit. Externally, all IC's look identical. Two integrated circuits are picked from a (single) randomly selected bo..

  Calculate magnitude of voltage v3 across the third impedance

a.Sketch the circuit diagram, the impedance diagram and the phasor diagram; take the supply voltage V as the reference phasor. b. Calculate the magnitude of the voltage V2 across the second impedance. c. Calculate the magnitude of the voltage V3 acro..

  Evaluate the pros and cons of using the snr and signal

Which of these metrics are dependent on link conditions: CINR, SNR, or BER Evaluate the pros and cons of using the SNR and signal - to - interference - noise ratio ( SINR ) for estimating signal quality versus using the absolute value of the signa..

  Determine the steady-state frequency deviation

Assuming that there is no frequency-dependent component of the load (i.e., D = 0), find the steady-state frequency deviation and the corresponding new generation of each unit. Use 1000 MVA as the p. u. (per-unit) base.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd