Determine what is the probability that all four have defect

Assignment Help Civil Engineering
Reference no: EM13309343

If the defect rate for the flash drivers is 0.5% and you randomly select four of them for inspection:

a) What is the probability that none of them has a defect?

b) What is the probability that all four have a defect?

c) What is the probability that the first one you select has a defect?

d) What is the probability that either one of four you select has a defect?

Reference no: EM13309343

Previous Q& A

  State how many spectra must be averaged in order to increase

How many spectra must be averaged in order to increase the signal-to-noise ratio of a spectrum from 7/1 to 20/1? i took 20/7 and squared

  What was the energy of the proton beam

The mass of a bottom quark is \(4.2 GeV/c^{2}\), What was the energy of the proton beam and how fast were they moving

  Determine what is probability of getting an 8gb flash driver

A manufactory company produces flash drivers and their products include: 1GB (10%), 2GB (10%), 4GB (20%), 8GB (30%), 16GB (20%) and 32GB (10%); in addition, there are four different colors for all the flash drivers

  Explain which expressions is not equivalent to ph

Which of the following expressions is not equivalent to pH? a. log 1/[H+(aq)] b. 14.0-pOH c. -log [H+(aq)] d. -log Kw/[OH-] e

  Find gauge pressure must the pump provide

Water is being pumped through a horizontal pipe that is 28.8 m long and 17.0 cm in diameter. what gauge pressure must the pump provide to give the same volume flow rate as for the first pipe

  Determine what was the intensity of the erthquaker

A city near the epicenter of an earthquake sustains major damage to poorly constructed building, althought hospital and schools designed to resist dmage from ground motion sustsain only minor damage.

  Discuss the theme of brotherly love

Discuss the theme of brotherly love, how does this theme juxtapose the characters of sonny and the narrator?

  Explain the change in interval energy of the gas is

A gas absorbs 0.0j of heat and then performs 35.6j of works. the change in interval energy of the gas is

  What fracture aperture is for single fracture to conduct

What would the aperture have to be if there were two fractures of equal aperture. For your calculations you can assume that the rock matrix that contains the fracture(s) has zero hydraulic conductivity.

  Determine the resulting speed of the cart

A 75-kg man is riding in a 75-kg cart at 1.0 m/s. He jumps off in such a way as to land on the ground with no horizontal velocity

Reviews

Write a Review

 

Similar Q& A

  Develop the relation between bulk unit weight

develop the relation between bulk unit weight, specific gravity, void ratio and weight of water.

  Determine the force required with an angle of 20 degrees

A 10 kg block is being pulled down a slope with an angle of 20 degrees and has a velocity of .2 m/s. Determine the force required

  Determine the magnitudes of the lift and drag

The forces acting on the sailplane are represented by three vectors. The lift L and drag D are perpendicular. The magnitude of the weight W is 500 lb. If the magnitude of the resultant of the three forces is 0

  Determine how far upstream of the section would be expected

The slope of the channel So=.15% and the Manning n=.038. Estimate the depth y2=100m upstream of a section where the flow depth y1=2.2m Using a) the direct integration method and b) the standard step method.

  Determine by trigonometry the required angle of forces

two forces applied as shown to a hook support. knowing that the magnitude of P is 35 N, determine by trigonometry the required angle if the resultant R of the two forces applied to the support is to be horizontal and the corresponding magnitude of..

  What is limiting depth of the exacavation to avoid heaving

An excavation is proposed for a site consisting of a homogenous, isotropic later of silt clay, 14.24 m thick, above a deep deposit of sand. The groundwater is 2m below ground level outside the excavation. The groundwater level inside the excavatio..

  Determine the x coordinate of center of gravity of pulley

A flat-belt idler pulley is molded from polystyrene with a bronze bushing. Knowing that the densities of polystyrene and bronze are 640 kg/m3 and 9100 kg/m 3, respectively, determine the x coordinate of the center of gravity of the pulley.

  Magnitudes of the additional loads

Determine the magnitudes of the additional loads that must be applied at B and F if the resultant of all six loads is to pass through the center of the mat.

  Provide a diagram showing the cost of the truss as function

A project for constructing a Facility just started. It involves the excavation of 40 to 60 feet deep and 60 feet wide trench to house double tunnels. A 24-inch outside diameter (22.5-inch inside diamater) water line is located in the path of the t..

  What is the maximum acceleration that the car can achieve

A car is traveling at 30 mph on a good, dry pavement at sea level. The front-wheel-drive car has a drag coefficient of 0.35, a frontal area of 30 ft2 and a weight of 2500 lbs. The wheelbase is 120 inches and the center of gravity is 20 inches from..

  Expected boiling-point elevation

What is the expected boiling-point elevation of water for a solution that contains 271 g of sodium chloride dissolved in 1.0 kg of water?

  Determine what is the pressure of methane in the balloon

helium gas contains trace amounts of methane. Consider a helium balloon pressurized to 5 psi. If methane molar mixing ratio is 800 ppmv, what is the pressure of methane in the balloon

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd