Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.Shaft is in tension; D1 = 3", D2 = 1", r at step is 0.1". Max stress has been calculated at 25,400 psi, but how do I calculate the largest hole I can drill in D2 and maintain stress near the hole at or below 25,400?
2.The homogeneous gate shown consists of one quarter of a circular cylinder and is used to maintain a water depth of 4m. That is, when the water depth exceeds 4m, the gate opens slightly and lets the water flow under it. Determine the weight of the gate per meter of length.
Primary treatment removes ~25 percent of the BOD. Calculate the volume (m3) and approximate hydraulic retention time (h) of the aeration basin required to run the plant as a "high rate" facility (F/M = 2 kg BOD/kg MLSS-day).
The flow rate of water flowing in a 3m wide channel is to be measured with a sharp-crested triangular weir 0.5m above the channel bottom with a notch angle of 60°. If the flow depth upstream from the weir is 1.5m
consider a spacecraft that is positioned directly between the earth and moon.the mass of the moon's is approximately 7.35 X10^22 kg, and at the instant under consideration, the moon is 3.8 X 10^8 km from earth.
Rope segment BC creates an angle of phi2 = 74.0^\circ with the floor and rope segment CD creates an angle theta with the horizontal. If both ropes BCA and CD can support a maximum tensile force T3 = 130 lb,
A sedimentation basin is used to remove suspended solids from a wastewater. The rate of flow of wastewater into the tank is 10 L/s, and the influent concentration of suspended solids is 200 mg/L.
The base engine develops 200 ft-lb of torque, and a modified version of the engine develops 240 ft-lb of torque. If the overall gear reduction ratio is 8 to 1, what is the maximum acceleration from rest (in ft/sec^2) for:
a) The maximum flow rate that can be achieved without cavitation occurring in the piping system. b) The maximum elevation of the highest point of the piping system to avoid cavitation.
During a snowstorm the fluoride feeder in North Bend runs out of feeder solution. The rapid mix tank is connected to a 5-km long distribution pipe. The flow rate into the rapid mix tank is 0.44m^3/sec, and the volume of the tank is 2.50 m^3.
A pressure gage at elevation 4.8 m on the side of a storage tank containing oil reads 34.7 kPa.Another gage at elevation 2.2 m reads 57.5 kPa. Compute the specific weight, density, and specific gravity of the oil.
Is the system within membrane manufacturer's warranty requirement of maximum flux rate of 14 gfd? What is the annual power cost of the RO system?
Water flows into and out of a 5 liter tank at a rate of 1 L/min. Within the tank, the mineral apatite is dissolving at a rate of 3x10^-10 moles of Si per m^2 per sec. If the tank contains 10g of the apatite with a specific surface area of 2 m^2/g,
Determine the number of completely mixed bioreactors (detention time of 45 min each) that would be required to meet the phenol discharge limit of 5 mg/L. The first-order removal rate constant is equal to 6.1 hr -1
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd