User Account

All Pages

Determine the value of the shear stress

Assignment Help Mechanical Engineering
Reference no: EM131123014

At a point in a piece of elastic material direct stresses of 90 MN/m2 tensile and 50 MN/mZ compressive are applied on mutually perpendicular planes. The planes are also subjected to a shear stress. If the greater principal stress is limited to 100MN/mZ tensile, determine:

(a) the value of the shear stress;

(b) the other principal stress;

Reference no: EM131123014

Questions Cloud

Discuss four exemptions and explain reasons why they exist : Discuss four exemptions and explain reasons why they exist. Then further discuss whether those communications should continue to be granted such a privilege; if you agree support your position, if you disagree, do likewise.
Determine the maximum stress set up due to compressive load : Assuming that, before loading, there is an initial sinusoidal curvature of the strut with a maximum deflection of 5 mm, determine the maximum stress set up due to a compressive end load of 200 kN. E = 208 GN/m2
Calculate the torque which can be transmitted by the tube : A steel tube has a mean diameter of 100mm and a thickness of 3 mm. Calculate the torque which can be transmitted by the tube with a factor of safety of 2.25 if the criterion of failure is maximum shear stress
Calculate the values of poisson ratio for the material : A bar of mild steel 25 mm diameter twists 2 degrees in a length of 250 mm under a torque of 430 N m. Calculate the values of E, G, K and Poisson's ratio v for the material
Determine the value of the shear stress : If the greater principal stress is limited to 100MN/mZ tensile, determine: the value of the shear stress; and the other principal stress
What is the firm total cost based upon the eoq : Vergas Enterprises wishes to determine the economic order quantity (EOQ) for a critical and expensive inventory item that it uses in large amounts at a relatively constant rate throughout the year. What is the firm's total cost based upon the EOQ c..
Determine the current weighted average cost of capital : Cascade Water Company (CWC) currently has 30 000 shares of common stock outstanding, trading at a price of R42 per share. Determine the current weighted average cost of capital for CWC
A network topology design for abc : For this project, you will design the layout of users, domains, trusted domains, anonymous users etc. for a start-up open-source software company, ABC. The company should have an internal CVS server (only internal developers can access it), an anonym..
A bias for industry from current drm : Evaluate the issue of whether or not the current DRM solutions are biased toward industry over the consumer. Support your evaluation with literature from both academic and industry sources.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Oil engine operating on ideal diesel cycle

An oil engine operating on the ideal diesel cycle has the overall compression ratio of 16:1, and the adiabatic expansion ratio or 8.75. The pressure and temperature at the beginning of adiabatic compression are 102.5 Kpa and 297K, respectively and th..

  Assuming that only caso3 is produced calculate the daily

assuming that only caso3 is produced calculate the daily production rate in tonsday of a 55-solids sludge from a

  Determine the net electric output

For a combined turbine-generator efficiency of 83%, determine the net electric output. Disregard the effect of the KE correction factors.

  A fallen tree trunk is damming up water in a creek the tree

a fallen tree trunk is damming up water in a creek. the tree trunk is approximately a cylinder 40 cm diameter and 4.0 m

  The temperature on the left edge of the wall

A one dimensional wall of material (Kw=10w/mk) is 50 mm thick with uniform heat generation q‘‘‘=5*10^6w/m^3. The left side is exposed to a fluid hl=500w/m^2k at 20 degree Celsius. The right side has a 10mm thick plate attached that has no heat genera..

  Derive a formula for the shortening d of the rubber cylinder

Derive a formula for the lateral pressure p between the rubber and the steel. (Disregard friction between the rubber and the steel, and assume that the steel cylinder is rigid when compared to the rubber.)

  What is the flow rate m3 of the gasoline and kerosene

crude oil is fractioned by two separating columns. the incoming crude oil is composed of the following weight fractions

  Design a combinational logic circuit

1. Design a combinational logic circuit which will add two 4-bit binary numbers. 2. Minimize the expression described in the truth table of Figure P12.50, and draw the circuit.

  Test to determine whether minicomputers actually average

Engineers claim that the variance of stripes is not more than 16 inches. Use the sample lengths given here from 12 measured stripes to test the variance claim. Assume stripe length is normally distributed. Let a = .05. Assuming that number o..

  Calculate the mass of vapor at the beginning and end of the

a closed and rigid tank with 1.5 m3 volume initially contains saturated vapor refrigerant 134a at 50deg c. the system

  A rigid tank has 01 kg saturated vapor r-410a at 0 celsius

a rigid tank has 0.1 kg saturated vapor r-410a at 0 celsius that is cooled to -20 celius by a -20 celcius heat sink.

  Determine the velocity of the particle as a function of

a particle is moving along a straight line with the acceleration a12t-3t12 fts2 where t is in seconds. determine the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd