User Account

All Pages

Determine the maximum stress set up due to compressive load

Assignment Help Mechanical Engineering
Reference no: EM131123017

A hollow circular steel strut with its ends fixed in position has a length of 2 m, an outside diameter of 100 mm and an inside diameter of 80 mm. Assuming that, before loading, there is an initial sinusoidal curvature of the strut with a maximum deflection of 5 mm, determine the maximum stress set up due to a compressive end load of 200 kN. E = 208 GN/m2.

Reference no: EM131123017

Questions Cloud

How has your experience been integrative towards your goals : How has your experience been integrative towards your academic or professional goals? How have you developed as a learner/thinker as part of your graduate studies at AMU/APUS?
The number of units in beginning inventory : Which of the following is not used in deciding how many units to produce in a period?
Evaluate the historical performance of the company : 1. Prepare four line graphs with the ratio on the vertical axis and the years on the hori- zontal axis for the following four ratios (rounded to one decimal place):
Discuss four exemptions and explain reasons why they exist : Discuss four exemptions and explain reasons why they exist. Then further discuss whether those communications should continue to be granted such a privilege; if you agree support your position, if you disagree, do likewise.
Determine the maximum stress set up due to compressive load : Assuming that, before loading, there is an initial sinusoidal curvature of the strut with a maximum deflection of 5 mm, determine the maximum stress set up due to a compressive end load of 200 kN. E = 208 GN/m2
Calculate the torque which can be transmitted by the tube : A steel tube has a mean diameter of 100mm and a thickness of 3 mm. Calculate the torque which can be transmitted by the tube with a factor of safety of 2.25 if the criterion of failure is maximum shear stress
Calculate the values of poisson ratio for the material : A bar of mild steel 25 mm diameter twists 2 degrees in a length of 250 mm under a torque of 430 N m. Calculate the values of E, G, K and Poisson's ratio v for the material
Determine the value of the shear stress : If the greater principal stress is limited to 100MN/mZ tensile, determine: the value of the shear stress; and the other principal stress
What is the firm total cost based upon the eoq : Vergas Enterprises wishes to determine the economic order quantity (EOQ) for a critical and expensive inventory item that it uses in large amounts at a relatively constant rate throughout the year. What is the firm's total cost based upon the EOQ c..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  During this process heat is transferred to maintain a

air is compressed in a variable-load piston-cylinder device equipped with a paddle wheel. initially air is at 500kpa

  Determine the systems thermal efficiency

Air enters a three-stage gas turbine at 100 kPa and 17 degree Celsius. This system uses a regenerator as well as reheating and interfolding. The pressure ratio across each compressor is 14.16; 300 kJ/kg of heat are added to the air in each combustion..

  Determine the pressure in lbfin2 at an intermediate state

a system consists of nitrogen n2 in a piston-cylinder assembly initially at p1 20 lbfin2 and occupying a volume of

  Assume the cost of electricity is 89 cents per kwh

an electrically driven pump operating at steady state is used to draw water from a pond. at the pump inlet the pressure

  However over time the effects of scoring diminish and the

water at atmospheric pressure boils on the surface of a large horizontal copper tube. the heat ?ux is 90 of the

  Estimate the daily heat loss through the wall

Assuming quasi steady conditions for which changes in energy storage within the wall may be neglected, estimate the daily heat loss through the wall if its total surface area is 200 m2.

  What is the retardation time

A plastic was stretched initially from 30 mm to 35 mm and then released at room temperature. The length changes with time were obtained as the following. Assume the Voigt model can be applied for this mechanical behavior.

  What is the value of the absolute mach number m1

What is the value of the absolute Mach number M1?

  Determine the water outlet temperature

If the water enters at Tm,i = 500 K and the surface temperature of the tube is Ts = 510 K, determine the water outlet temperature Tm,o.

  Determine outside air flow under the following outside air

a building has a 10000 ft.sq interior office space served by one ahu with economizer function. the supply air flow is

  A distillation column as shown in the figure to the right

a distillation column as shown in the figure to the right is a device used to separate components with different

  What is the thermal resistance associated with a wall that

consider a composite wall that includes an 8-mm thick hardwood siding 40mm by 130mm hardwood studs on .65m centers with

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd