User Account

All Pages

Calculate the torque which can be transmitted by the tube

Assignment Help Mechanical Engineering
Reference no: EM131123016

A steel tube has a mean diameter of 100mm and a thickness of 3 mm. Calculate the torque which can be transmitted by the tube with a factor of safety of 2.25 if the criterion of failure is (a) maximum shear stress; (b) maximum strain energy; (c) maximum shear strain energy. The elastic limit of the steel in tension is 225 MN/m2 and Poisson's ratio v is 0.3.

Reference no: EM131123016

Questions Cloud

The number of units in beginning inventory : Which of the following is not used in deciding how many units to produce in a period?
Evaluate the historical performance of the company : 1. Prepare four line graphs with the ratio on the vertical axis and the years on the hori- zontal axis for the following four ratios (rounded to one decimal place):
Discuss four exemptions and explain reasons why they exist : Discuss four exemptions and explain reasons why they exist. Then further discuss whether those communications should continue to be granted such a privilege; if you agree support your position, if you disagree, do likewise.
Determine the maximum stress set up due to compressive load : Assuming that, before loading, there is an initial sinusoidal curvature of the strut with a maximum deflection of 5 mm, determine the maximum stress set up due to a compressive end load of 200 kN. E = 208 GN/m2
Calculate the torque which can be transmitted by the tube : A steel tube has a mean diameter of 100mm and a thickness of 3 mm. Calculate the torque which can be transmitted by the tube with a factor of safety of 2.25 if the criterion of failure is maximum shear stress
Calculate the values of poisson ratio for the material : A bar of mild steel 25 mm diameter twists 2 degrees in a length of 250 mm under a torque of 430 N m. Calculate the values of E, G, K and Poisson's ratio v for the material
Determine the value of the shear stress : If the greater principal stress is limited to 100MN/mZ tensile, determine: the value of the shear stress; and the other principal stress
What is the firm total cost based upon the eoq : Vergas Enterprises wishes to determine the economic order quantity (EOQ) for a critical and expensive inventory item that it uses in large amounts at a relatively constant rate throughout the year. What is the firm's total cost based upon the EOQ c..
Determine the current weighted average cost of capital : Cascade Water Company (CWC) currently has 30 000 shares of common stock outstanding, trading at a price of R42 per share. Determine the current weighted average cost of capital for CWC

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Design a symmetric 4-bar mechanism optimized for a constant

design a symmetric 4-bar mechanism optimized for a constant velocity of 150 insec over a straight line motion of 8 such

  Design a container using differentiation

design a container using differentiation that has a volume of 2500 litres. it must use the minimum amount of material.

  Floor space of any facility that houses shell

The floor space of any facility that houses shell-and- tube heat exchangers must be  sufficiently  large  so the tube bundle can be serviced easily. A rule of thumb is that the floor space must be at least 2.5 times the length of the tube bundle s..

  The rod must stretch less than 0125 mm determine an

an engineer determines that a 40 cm long rod of 1020 grade steel will be subjected to a tension of 20 kn. the following

  Determine the values of the constants

Determine the values of the constants A and σ o for the material. [Remember that the tensile strength is the maximum engineering stress.]

  What is the steady state amplitude of the vertical response

Consider just the vertical (y) response of the system when the beam is being stretched. Show that the spring constant, ka, is approximately 70.6 mN/m. What is the steady state amplitude of the vertical response? See Figure A below for an engine..

  If the correction is not made at what car speed will

the rotating parts of a front wheel assembly of a car have a total mass of 35 kg and are measured to be out of balance.

  Determine a the rate of power generation for average wind

the average wind speed on the north texas plains around amarillo is approximately 6 ms. an efficient wind turbine can

  Consider a cylinder transistor diameter 04 cm and length 05

consider a cylinder transistor diameter 0.4 cm and length 0.5 cm that dissipated 0.2w power onto 30c transistor1

  Assuming that flow is steady and incompressible obtain a

an incompressible fluid flows past in a solid plate.the x and y coordinates are measured from the leading edge of the

  How much power will the cycle produce when it is executed

an air standard dual cycle has a compression ratio of 18 and a cutoff ratio of 1.1. the pressure ratio during the

  How to convert the uneven diameter of the hollow tube in to

a solid hollow tube thin wall with pin in the bottom and the top part is connect with another tube and there is a force

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd