Determine the thickness of the oil film assuming a linear

Assignment Help Civil Engineering
Reference no: EM13564967

1.If the municipal water rate is one dollar per thousand gallons, how many pounds of water are delivered to the customer's house for one dollar?

2.Rainwater from California is said to contain 0.3 mg/L of silica. What is the silica concentration in the rainwater in ppt, ppb, molarity, and% solution

3.A solid cube with a side length of 0.4 ft and a weight of 110 lb slides down a smooth surface that is inclined at 45 degrees to the horizontal. The block slides on a film of oil with a viscosity of 1.85 x 10-2 lb-s/ft2. If the velocity of the block is 1.2 ft/s, determine the thickness of the oil film assuming a linear velocity distribution in the film.

Reference no: EM13564967

Questions Cloud

Find the bottom width and the depth of water channel : A simply supported beam carries with a span of 7.5 m carries a uniformly distributed load of 25 N/mm. if the maximum allowed deflection of the beam is 1/325 of its span, detemine the cross-sectional dimensions of the beam. assume the beam has a recta..
Determine the initial temperature and total enthalpy in the : A 10 kg of refrigerant R-134a at 300 kPa fills rigid container whose volume is 14 L. The container is then heated until the pressure is 600 kPa.
What is the mean time between counts : Suppose the counts recorded by a Geiger counter follow a Poisson process with an average of three counts per minute.
Find the bottom width and the depth of water channel : The rate of flow through a trapezoidal open channel is 20 m^3/s and the mean velocity of flow is 1m/s . the side slope is 1:1 and the bed slope is 1 in 5000. Assume Chezy's constant C as 60, find the bottom width and the depth of water channel.
Determine the thickness of the oil film assuming a linear : A solid cube with a side length of 0.4 ft and a weight of 110 lb slides down a smooth surface that is inclined at 45 degrees to the horizontal. The block slides on a film of oil with a viscosity of 1.85 x 10-2 lb-s/ft2. If the velocity of the block i..
What is the diameter of the capillary tube assuming it has : You are designing a new thermometer using Galinstan, an alloy of gallium, indium, and tin that is a liquid at normal living temperatures. The coefficcient of thermal expansion is 190*10^-6 (1/kelvin).
What percentage of the time will the through lane adjacent : A traffic engineer is trying to design a left turn bay on an EB approach to an intersection. The signal timing for left turns will have 10 seconds of “left turn only” green time and 50 seconds of red time each signal cycle. The green time will be suf..
Estimate the evaportranspiration losses for the area : Adriana wishes to accumulate $2,020,000 in 35 years. If 35 end-of-year deposits are made into an account that pays interest at a rate of 7% compounded annually, what size deposit is required each year to meet Adriana's stated objective?
How many cubic meters of borrow pit material is needed : The water content at 95% compaction is 11% on the dry side and 12% on the wet side of the compaction curve. What is the minimum additional weight of water per unit volume to achieve 95% Proctor compaction?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is break even point and when would be better to choose

A car dealership offers $2000 cash back; financing at 3.49% APR for 60 months or 0% APR for 60 months when you purchase a car. What is the break even point and when would it be better to choose one option over the other.

  What is the maximum feed rate that can be accommodated

Vapour from the second effect is condensed at a pressure corresponding to 325 K. The heat transfer area is 10 m2 and the overall heat transfer coefficients are 3 and 2 kW/m2 in the first and second effects respectively.

  Determine the coordinates of the center of curvature c at t

A particle which moves with curvilinear motion has coordinates in meters which vary with time t in seconds according to x = 3.3t2 + 3.1t - 5.3 and y = 5.1t - 4.0. Determine the coordinates of the center of curvature C at time t = 1.9 s.

  Atual discharge of a water pipeline

If the elevation difference between the water surfaces is y = 25 + x/11 metres, what minimum pipeline diameter will be required to convey the design discharge? Once your design is complete, determine the actual discharge. The value of x equals 23.

  Design hardwood beam to support a uniformly distributed load

Design a hardwood beam to support a uniformly distributed load of 20 kN over a simply supported span of 8 m. consider bending strength only. Assume that the weight of the beam is 2 kN.

  Determine thethickness of the water layer under the runners

A sled with two runners slides along a thin horizontal layer ofwater between the ice and the runners. The horizontal force thatthe water puts on the runners is equal to 1.2 lb when the sled'sspeed is 30 ft/s.

  Determine elevation vs surface area relationship for vault

An underground storage vault is to be constructed to serve as a detention pond for a heavily urbanized area. The walls of the vault will be vertical, but the flow will be sloped along its length to promote drainage.

  Determine the safe load the column can carry using working

A column of dimensions 200 X 300 mm has an effective length of 3m. It is reinforced with 6 HYSD bars of 20mm diameter. Determine the safe load the column can carry using working method of design. Using M20 Concrete.

  Determine appropriate dimensions of the finished water

Cylinders C and D are attached to the end of the cable. if D has a mass of 600 kg, determine the required mass of C, the maximum sag h of the cable, and the length of the cable between the pulleys A and B. The Beam has a mass per unit length of 50 kg..

  Cause of heading-up of the water surface

A rectangular channel 2.0 m wide carrying a discharge of 2.5 m3/s is to be fitted with a weir at its downstream end to provide a means of flow measurement as well as to cause heading-up of the water surface.

  Calculate the depth h of mud for which the 3m concrete

Calculate the depth h of mud for which the 3m concrete retaining wall is on the verge of tipping about its forward edge A. the density of mud may be taken to be 1760 kg/m3 and that of concrete to be 2400 kg/m3.

  Determine the normal depth using a converging iteration

A 5-m wide rectangular channel is carrying a flow of 5 cubic meter per second. If the Manning n=0.013 and the bottom slope, So=0.0001, determine the normal depth using a converging iteration.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd