Determine the the max weight of the block

Assignment Help Civil Engineering
Reference no: EM13309828

Determine the the max weight of the block that the system does not fail if the max tension that can be developed in cable DB is 100N and the max compression that can be developed in tower CD is 100N.

Reference no: EM13309828

Questions Cloud

What is the nominal strength with one end fixed : The length is 10 feet. What is the nominal strength if Fy=50 ksi. Note that this is a slender-element compression member, and the equations of AISC section E7 must be used
What would side slope of cut be if catch point is located : A backsight reading of 2.56 was obtained with rod at A and a foresight reading of 7.45 was obtained with the rod at the trial point B. If B is located 37.00 feet from the center line of a planned 50-foot wide road, is the catch point located uphi..
Determine the acre-feet of water that can be impounded : An earth fill is constructed across a drainage. Closed contours at the 1000, 1040 and 1080 foot levels define areas of 680,000; 1,200,000; and 1,325,000 square feet respectively.
Obtain the net torque on the wheel : A Ferris wheel accelerates from rest to an angular speed of 1.5 rad s-1 in 12 s. what is the net torque on the wheel
Determine the the max weight of the block : Determine the the max weight of the block that the system does not fail if the max tension that can be developed in cable DB is 100N and the max compression that can be developed in tower CD is 100N.
Compute the rms voltage across the secondary : A 12 DC power supply is connected to the primary coil of a transformer. What is the rms voltage across the secondary
Calculate the magnification of the object : sketch a scaled ray diagram and show the location of the iamge using 3 principle rays, calculate the magnification of the object
What change in performance/evaluation you would gain : Why you think this topic is important? why is this a significant area of research? What are the main problems in this area? and why do you think your proposal is important for the topic?
The primary care clinic : The Primary Care Clinic

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the force exerted by the jet on the vane

A pipeline terminates in a nozzle of outlet diameter = 0.15 m. The free jet from the nozzle is deflected through 120º by a vane as shown. Water flow rate through this pipe is 0.25 m3/s. Ignoring friction, find the force exerted by the jet on ..

  Determine the deflection angle to the last full station

Determine the deflection angle to the last full station on a horizontal curve with Da=3 degrees. The PI is located at station 12.20 and the central angle is 24 degrees.

  Determine how many units of each product company should make

The number of hours on each machine required to produce a product is given in the following table, along with the number of hours available per week on each type of machine. Assume that the company can sell everything it produces.

  Determine minimum diameter required for a solid drive shaft

The engine of an automobile supplies 180 hp at 2500 rpm to the drive shaft. If the maximum shearing stress in the drive shaft must be limited to 6 ksi, determine the minimum diameter required (in inches) for a solid drive shaft.

  Determine the rate of flow-unconfined aquifer

In an unconfined aquifer having K = 30/m/day, two observation wells, 3km apart, have water levels of 50 and 40 m, respectively, above the base of the aquifer. Determine the rate of flow.

  Arrival of vehicles according to a poisson process

At a specified point on a highway, vehicles are known to arrive according to a Poisson process. Vehicles are counted in 20-second intervals, and vehicle counts are taken in 120 of these time intervals.

  What should be the minimal diameter of the above tank

For an elevated storage tank , if the minimum allowable pressure = 300 kPa, Height of pipe system at low-pressure service location = 6 m, and head loss from tank to service location: average daily conditions = 11 m

  Determine the angle that vo forms with vertical by rocket

If the rocket's decent parachute does not deploy and the rocket lands 340 ft from A, determine the angle (alpha) that vo forms with the vertical, the maximum height h reached by the rocket, and the duration of the flight.

  Calculate kg per day of sludge process if sludge is solid

The effluent contains 20 mg/L of solids and 20 mg/L of BOD the biological treatment process produced .32 kg of bacterial solids per kg of BOD removed

  How far does a horizontal plane depart from a level surface

The width of a lake is 16 km (it is a flat plane tangent to the radius of the sphere). How far does a horizontal plane depart from a level surface if the earth is a sphere with r=6371km

  Determine the magnitude of the velocity of the collar

The undeformed length of the spring is l. Knowing that the collar is released from rest at x = and neglecting friction between the collar and the horizontal rod, determine the magnitude of the velocity of the collar as it passes through point C.

  Position of the race car when acceleration is given

Starting from x = 0 with no initial velocity, the acceleration of a race car is defined by the relation a = 6.8e- 0.00057x , where a and x are expressed in m/s 2 and meters, respectively. Determine the position of the race car when v = 30 m/s.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd