Determine the specific gravity of the sand

Assignment Help Civil Engineering
Reference no: EM13554993

1.A wet sand sample has a volume of 4.63 * 10^-4 m^3 and weighs 8 N. After oven-drying, the weight reduces to 7.5 N. Calculate the water content, void ration, and degree of saturation.

2.The wet mass of a sample of saturated soil is 520 grams. The dry mass, after oven-drying, is 400 grams. Determine the a) water content b)void ration c)saturated unit weight, and d)effective unit weight

3.The gas tank of a car is filled with a nozzle that discharges gasoline at a constant flow rate. Based on unit considerations of quantities, write a relation for the filling time in terms of the volume (V ) of the tank in liters (L) and the discharge rate of gasoline (dV/dt) in terms of L/s.

4.A cylinder has 500cm^3 of water. After a mass of 100 grams of sand is poured into the cylinder and all air bubbles are removed by a vacuum pump, the water level rises to 537.5 cm^3. Determine the specific gravity of the sand.

Reference no: EM13554993

Questions Cloud

Do the results of this experiment support your analysis : Under the right conditions, it is possible, due to surface tension, to have metal objects float on water. Consider placing a short length of a small diameter steel (sp. wt. =460 lb/ft^3) rod on a surface of water
Find the safety factor of the wire against breaking : A closed tank is filled with a liquid. The pressure at the top of the tank is less than atmospheric pressure. Which of the following accurately represents the gage pressure distribution on the surface indicated?
Determine the mass flow rate the power produced : A Rankine cycle has a boiler pressure of 2500 psi and a condenser pressure of 1psi. The temperature at the inlet of the turbine is 800F. The turbine has an isentropic efficiency of 90 percent and the pump operates isentropically.
Determine the water content void ratio saturated unit weight : The wet mass of a sample of a saturated soil is 520grams. the dry mass, after oven-drying, is 400grams. determine the water content, void ratio, saturated unit weight, and effective unit weight.
Determine the specific gravity of the sand : A cylinder has 500cm^3 of water. After a mass of 100 grams of sand is poured into the cylinder and all air bubbles are removed by a vacuum pump, the water level rises to 537.5 cm^3. Determine the specific gravity of the sand.
Determine the tradeoff between the cost and the energy head : Two materials (wrought iron, ks = 0.046 mm, and galvanized iron, ks = 0.15 mm) are being considered for a new pipeline. The expected discharge is 0.15 m3/s. Both the head loss and cost are sought for. Wrought iron pipe costs 5 cents more than the gal..
What is the maximum theoretical coefficient of performance : The low temperature in a freezer is -20 C, and the discharge temperature is 35 C. What is the maximum theoretical coefficient of performance
What is the kinetic energy just before it hits the earth : a 3 kg cylinder falls vertically from rest in a very tall, evacuated tube 20 m above the surface of the earth. what is the kinetic energy just before it hits the earth
Journalize transaction - debit analysis : Purchased $450 of supplies on account and indicate what accounts are increased and decreased by each transaction. Debit Analysis Credit Analysis 1. 2. 3.

Reviews

Write a Review

Civil Engineering Questions & Answers

  A continuously reinforced concrete pavement cross section

what is your recommendation for the maximum size of coarse aggregate for the following situation? a continuously

  Determine the largest loadwhich can be applied

A block of 250mm length and 50x40mm cross section is tosupport a centric compressive load P. The material to be usedis a bronze for which E = 95GPa. knowing that the normal stress must notexceed 80 MPa and that the decrease in length of the block sho..

  What is the standard deviation of total weekly waiting time

Suppose your wait time for a shuttle bus in the morning is normally distributed with µ=8 minutes and t1=5 minutes. Due to increased congestion in the afternoon, your wait time for a shuttle bus in the afternoon is normally distributed

  Determine allowable stress design reference and values

determine the Allowable Stress Design (ASD) reference and adjusted design values for the following members and loading conditions. All members are No. 2 Hem-Fir and are fully braced to prevent lateral-torsional buckling.

  Draw a flow net show flow lines flow channels and

draw a flow net. show flow lines flow channels and equipotential lines. using flow nets please provide an estimate of

  Provide a reasonable design for a efficient esp treating

The particles have an effective drift velocity of 10.0 cm/s. Specify the total plate area, channel width, number and size of plates, number of electrical sections (total and in direction of flow), and total corona power to be supplied, and estimat..

  Determine what is the largest value of the force f

The weight of the box is 20 lb and the coefficient of static friction between the box and the floor = 0.65. Neglect the weights of the bars. What is the largest value of the force F that will not cause the box to slip

  What contour interval will be drawn if 50ft interval is used

An area that varies in elevation from 463ft - 634ft is being mapped. What contour intervals will be drawn if a 50ft interval is used. Which lines are emphasized.

  Determine what is the number concentration

An aerosol with a lognormal size distribution has a count median diameter of 2.0 micron and a geometric standard deviation of 2.2. If the mass concentration is 1 mg/cubic meter what is the number concentration

  Construct a choice table for interest rates from

QZY, Inc. is evaluating new widget machinesoffered by three companies. The machines have the following characteristics:

  Calculate the normal force n exerted by the side of the slot

The flat circular disk rotates about a vertical axis through O with a slowly increasing angular velocity. Prior to rotation, each of the 0.60-kg sliding blocks has the position x = 29 mm with no force in its attached spring.

  Determine the net rate of flow of linear momentum

Determine the net rate of flow of linear momentum through the control surface.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd