Determine the rate of heat transfer to the pan

Assignment Help Civil Engineering
Reference no: EM131030574

discuss the following question in detail

Repeat Prob. 3-43 for a location at 2000-m elevation where the standard atmospheric pressure is 79.5 kPa.

Prob. 3-43

Water is boiled at 1 atm pressure in a 25-cm-internaldiameter stainless steel pan on an electric range. If it is observed that the water level in the pan drops by 10 cm in 45 min, determine the rate of heat transfer to the pan.

Reference no: EM131030574

Questions Cloud

Calculate the duration of the nfls liability : How much money should the NFL invest in its bond portfolio today to fully fund its future liability? Calculate the duration of the NFL's liability.
Describe the relationship between the two containers : A prune juice contanier is a rectangular prism that measure 12 inches by 3.5 inches by 4 inches. Describe the relationship between the two containers answer using l*w*h.
Discuss data networking standards and recalling names : Describe and discuss data networking standards, recalling names, and order of the seven layers of the OSI reference model and the TCP/IP protocol stack. Discuss the different protocols that make up the TCP/IP suite, including: IP, TCP, UDP, ARP, a..
What is relationship of water table to surface topography : In Figure 1, what is the relationship of the water table to surface topography? Considering the cost of drilling and operating a ground-water well, where would you site the least expensive well?
Determine the rate of heat transfer to the pan : Water is boiled at 1 atm pressure in a 25-cm-internaldiameter stainless steel pan on an electric range.
Demonstrate your ability to plan and budget : Demonstrate your ability to plan and budget  - demonstrate your understanding of the concepts, understandings and processes that have been introduced in this unit and
Design the new addressing scheme for the network : Design the new addressing scheme for the network through the use of graphical tools in Microsoft Visio or an open source alternative such as Dia. Note: The graphically depicted solution is not included in the required page length.
Determine the temperature at which the liquid in the tank : Now the water is slowly heated. Determine the temperature at which the liquid in the tank is completely vaporized. Also, show the process on a T-v diagram with respect to saturation lines.
What are the different types of media : What are the different types of media that can be used to connect different computers together into a computer network? Twisted pair cables are used for connecting computers to a network. Distinguish between straight-through and crossover cable con..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the maximum flow rate that can be pumped

assume the pipe diameter is 4-inches, (f = 0.035), Distance from BC is 15-feet, distance DE is 180-feet and z = 60-feet. The elevation of C is 10-feet above the lower water surface.

  What constant gas pressure is required of the area

a 2kg piston accelerates to 20m/s from rest. what constant gas pressure is required if the area is 10cm^2, the travel is 10cm and the outside pressure is 100Kpa

  Determine the smallest allowable value of p if slipping

A recording tape passes over a 20-mm radius drive drum B and under the idler drum C. Knowing that the coefficents of friction between the tape and the drums are us=.40 and uk=0.30 and that drum C is free to rotate, determine the smallest allowable va..

  Which is estimated at 1 billion had that rate continued

World population 10,000 years ago has been estimated at about 5 million. what exponential rate of growth would have resulaed in the population in 1850 , which is estimated at 1 billion had that rate continued

  Determine what is the radial-horizontal stress at the point

A tire carries a 5,000-lb load and has a pressure of 100 psi. The pavement has a modulus of elasticity of 43,500 psi. A deflection of 0.016 inches is observed at a point on the pavement surface 0.8 inches away from the tire load.

  Calculate the minimum required wall thickness t-min

A tubular aluminium bar (G=28GPa) of square cross section with outer dimensions 50mm x 50mm must resist a torque T=300Nm. Calculate the minimum required wall thickness t_min if allowbale shear stress is 20MPa

  Freeways density and level of service

What will the freeway's density and level of service be before and after the ban? (Assume that the trucks are removed and all other traffic attributes are unchanged).

  Find temperature at which air must leave heat exchanger

Gaseous oxygen (99% pure, molar basis) is to be produced at a rate of 350ft^3/hr in a Linde single column plant. The column operates at a pressure of 1 atm. Air leaves the compressor at a pressure of 10 atm.

  Determine the horizontal and vertical components of reaction

Determine the horizontal and vertical components of reaction at the supports. Neglect the thickness of the beam

  Design a circular radial-flow clarifier for a town

Design a circular radial-flow clarifier for a town with a projected population of 45,000. Assume that the wastewater flow is 400 L/capita-day. Size the system for a 2-hr detention time at average flow.

  What will be the decrease in the volume of the block

A rectangular block of aluminum 30 mm × 60 mm × 90 mm is placed in a pressure chamber and subjected to a pressure of 100 MPa. If the modulus of elasticity is 70 GPa and Poisson's ratio is 0.333

  What is max mole fraction of methanol that can be achieved

A solution containing 30% methanol (by mol) is flashed to 1 bar, 70.82°C. Determine the phase of the system; if 2 phases, report the compositions and relative amounts of each phase.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd