Determine the number of turbines required

Assignment Help Mechanical Engineering
Reference no: EM131057197

A hydroelectric power station is required to generate a total of 4.2 MW from a number of single-jet Pelton wheel turbines each operating at the same rotational speed of 650 rpm, at the same power output and at a power specific speed of 1.0 rev. The nozzle efficiency ηN of each turbine can be assumed to be 0.98, the overall efficiency ηo is assumed to be 0.88, and the blades speed to jet speed ratio v is to be 0.47. If the effective head HE at the entry to the nozzles is 250 m, determine

a. the number of turbines required (round up the value obtained);

b. the wheel diameter;

c. the total flow rate.

Reference no: EM131057197

Questions Cloud

Income statement net of applicable income taxes : All of the following components are shown in the income statement net of applicable income taxes EXCEPT (a) gain or loss on sale of plant assets. (b) extraordinary gain or loss. (c) cumulative effect of a change in accounting principle. (d) discontin..
What is the value of the equilibrium constant : Consider the following reaction: NH4HS(s)?NH3(g)+H2S(g) An equilibrium mixture of this reaction at a certain temperature was found to have [NH3]= 0.274 Mand [H2S]= 0.370 M. What is the value of the equilibrium constant (Kc) at this temperature?
Gain or loss on sale of plant assets : All of the following components are shown in the income statement net of applicable income taxes EXCEPT (a) gain or loss on sale of plant assets. (b) extraordinary gain or loss. (c)cumulative effect of a change in accounting principle. (d) discontinu..
What is annual operating cash flow from proposed project : The Wolf's Den Outdoor Gear is considering replacing the equipment it uses to produce tents. The equipment would cost $1.4 million and lower manufacturing costs by an estimated $215,000 a year. The equipment will be depreciated over 8 years using str..
Determine the number of turbines required : A hydroelectric power station is required to generate a total of 4.2 MW from a number of single-jet Pelton wheel turbines each operating at the same rotational speed of 650 rpm, at the same power output and at a power specific speed of 1.0 rev
Determine the reactants or products : The reaction below has an equilibrium constant Kp=2.2×106 at 298 K.  2COF2(g)?CO2(g)+CF4(g) Express your answer using two significant figures. A. Calculate Kp for the reaction below. 4COF2(g)?2CO2(g) +2CF4(g) Predict whether reactants or products w..
Bonds of equivalent risk yield-find market value of bonds : AB bonds carry a 10% annual coupon, have a $1,000 face value and mature in 4 years. Bonds of equivalent risk yield 15%. Find the market value of AB bonds. AB is in financial difficulty and has asked its bondholders to accept the following deal. The f..
Prepare a paper about must pertain to operating systems : Prepare a Research paper about Must pertain to operating systems.
Determine the reynolds numbers for both the hot and cold : Assuming dynamically similar conditions between those of the laboratory and the projected design determine, for the "cold" test, the equivalent mass flow rate and the speed of rotation. Assume the gas properties are the same as for air

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Standard machining parameter formulae for milling

Using the standard machining parameter formulae for milling, determine the speed (rpm), feed (ipm) and machining time (TM) recommended to horizontal mill ANSI #1018 cold rolled steel that is 1.50 inch long with a 10 tooth 4.0 inch diameter slab mill ..

  Determine mass flow rate at inlet and velocity

Steam at 80 bar, 440 Celsius, enters a turbine operating at steady state at a volumetric flow rate of 180 m3/min. The water exits the turbine in two streams, 20% as exits through a 0.25 m diameter pipe at 60 bar, 400 Celsius. The rest exits through a..

  What is the total current

A 60 ohm, 40 ohm, and 20 ohm resistor are each connected in parallel across a 120VAC source. What is the total current.

  A 12 kn force is exerted on a rocker arm the moment of

a 12 kn force is exerted on a rocker arm. the moment of inertia i of the crosssectionnbspwith respect to the

  For an actuator that has an inside diameter of 050 in and a

a measure of stiffness of a linear actuator system is the amount of force required to cause a certain linear

  Find how much should be cut off from free length of the

a helix compression spring is manufactured using the following parametersod1.00id.790wire dia 0.105fo 40.49 lbf

  A projectile is fired with an initial speed of 633msat an

a projectile is fired with an initial speed of 63.3msat an angle of 43.7circ above the horizontal on a long flat firing

  A power drive shaft is designed with a safety factor of 8

a power drive shaft is designed with a safety factor of 8. the shaft is subjected only to torsional load torque. if the

  Determine the rate of entropy generation in the wall and

consider steady heat transfer through a 5m x 6m brick wall of a house of thickness 30 cm. on a day when the temperature

  Effective mass of electrons in a conduction band

Since the effective mass of electrons in a conduction band decreases with increasing curvature of the band according to eq. (3-3), comment on the electron effective mass in the Valley of GaAs compared with the indirect X or L valley.

  A well-insulated piston-cylinder assembly is connected by a

a well-insulated piston-cylinder assembly is connected by a valve to an air supply line at 8 bar. initially the air

  The shaft supports a single concentrated mass at its center

a consider a simply-supported low-alloy steel shaft ten feet in length and two inches in diameter. the shaft supports

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd