Find how much should be cut off from free length of the

Assignment Help Mechanical Engineering
Reference no: EM13629735

A helix compression spring is manufactured using the following parameters:

OD=1.00

ID=.790

(wire dia 0.105)

Fo = 40.49 lbf (operating force)

Lo = 2.68 (operating length)

Fi = 32.650 (Force at installed length)

Li = 3.30 (Installed length

Active Coils 18.436

Total Coils 20.436

Material: Stainless 17-7 with 27449psi as Minimum Tensile Strength

a) Find how much should be cut off from free length of the spring to reduce the Fo from 40.49 to 31.3 lbf? Assuming that the lengths of Lo and Li stay the same.

b) Find the Fi that is a result of the Fo.

Reference no: EM13629735

Questions Cloud

The size of fish in a lake follows a normal distribution : the size of fish in a lake follows a normal distribution with mean m 1 lb 4 oz and standard deviation s 3 oz . fish
A diatomic calorically perfect ideal gas in a : a diatomic calorically perfect ideal gas in a piston-cylinder assembly undergoes a cycle from 1 to 2 is isothermal from
A spherical hot-air balloon is initially filled with air at : a spherical hot-air balloon is initially filled with air at 120 kpa and 35oc with an initial diameter of 3 m. air
A certain type of engine suffers a critical failure with : a certain type of engine suffers a critical failure with probability 1.59 each start.a. what is the probability of a
Find how much should be cut off from free length of the : a helix compression spring is manufactured using the following parametersod1.00id.790wire dia 0.105fo 40.49 lbf
Then heat is removed to bring the pressure back down to 1 : these problems are in a cycle context. in this cycle air is first compressed in a piston-cylinder cylinder assembly in
A basket of 1000 parts is selected at random from a : a basket of 1000 parts is selected at random from a shipment of 50 baskets. the chance of any single part being
Iq test scores are normally distributed with a mean of 100 : iq test scores are normally distributed with a mean of 100 and a standard deviation of 15. an individual?s iq score is
A stone is shot from the edge of a cliff 125 m above ground : a stone is shot from the edge of a cliff 125 m above ground level with an initial speed of 65 ms at an angle of 37

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine a velocity versus time graph of their descent and

a skydiver of weight 84kg jumps from a plane 3300m above the ground. they initially free fall for a period of seconds

  What force would be required to start a 250lb crate

what force would be required to start a 250lb crate sliding across a cement floor which has a coefficient of static

  What is the concept they understood

To solve ax = b Find a number y such that ay is integer (and possibly a factor of b) Then if k Ay = b, the answer is ky What is the concept they understood?

  Steam entering a nozzle has an enthalpy of 3200 kjkg and

steam entering a nozzle has an enthalpy of 3200 kjkg and its intial velocity is 75 ms. the exit stream has an enthalpy

  100 lb of fluid food is heated by addition of 10000 btu of

100 lb of fluid food is heated by addition of 10000 btu of energy. if the food has initial temperature of 40degf and

  What is the biot number of this cooling situation would

an aluminum cube initially at 400oc with a dimension of 2 cm on each side is cooled using 30oc air with a convection

  How long will it be before the exiting water reaches 38c

a residential hot water heater initially contains water at 60c degree celcius someone turns on a shower and draws water

  If the dislocation is pi nned at two points 1 micron apart

a sample of tungsten w contains an edge dislocation. w can be treated as elastically isotro pi c and the dislocation is

  It is desired to compare the results of property

it is desired to compare the results of property predictions for water near or in the saturation region using a the

  What steady-state creep rate would you predict for this

estimate the activation energy for creep for the low carbon nickel alloy using the following temperature dependence of

  The energy loss in the system is 25 times the velocity head

the pump is delivering hydraulic oil with a specific gravity of 0.85 at a rate of 20 gallons per minute. the pressure

  Calculate the volume flow rate of the steam at the

steam enters the adiabatic condenser i.e.heat exchange of a steam power plant at 20 kpa 95 percent quality and with a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd