User Account

All Pages

A projectile is fired with an initial speed of 633msat an

Assignment Help Mechanical Engineering
Reference no: EM13604911

A projectile is fired with an initial speed of 63.3m/sat an angle of 43.7^\circ above the horizontal on a long flat firing range.

Determine the maximum height reached by the projectile.
Determine the total time in the air.
Determine the total horizontal distance covered (that is, the range).
Determine the speed of the projectile 1.86s after firing.
Determine the direction of the projectile 1.86s after firing.

Reference no: EM13604911

Questions Cloud

Jones co can further process product b to produce product c : jones co. can further process product b to produce product c. product b is currently selling for 45 per pound and costs
A professional tennis player hit 100 balls and their speeds : frequency table speednumber of balls 0 - 29430 - 591660 - 896090 - 11920a professional tennis player hit 100 balls and
A lens with a focal length of 15 cm is placed 45 cm in : a lens with a focal length of 15 cm is placed 45 cm in front of a lens with a focal length of 5.0 cm. how far from the
Assume that your credit card has a 15422 percent rate what : assume that your credit card has a 15.422 percent rate. what would your finance charge be using the following table if
A projectile is fired with an initial speed of 633msat an : a projectile is fired with an initial speed of 63.3msat an angle of 43.7circ above the horizontal on a long flat firing
Soap company manufactures soap x and soap y and can sell : soap company manufactures soap x and soap y and can sell all it can make of either. based on the following data if soap
Concepts and applications find the range and standard : concepts and applicationsfind the range and standard deviationold faithful geyser time intervals in minutes between
A mass on a string of unknown length oscillates as a : a mass on a string of unknown length oscillates as a pendulum with a period of 2.2s . parts a to d are independent
Describing distribution the reaction times of 500 randomly : describing distribution the reaction times of 500 randomly selected drivers measured under standard conditions.a. how

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A projectile is launched with a speed v0 270 ms from the

a projectile is launched with a speed v0 27.0 ms from the floor of a 4.3-m-high tunnel as shown. determine the maximum

  If the pressure is 10 psi at the 2in diameter section find

fluid is flowing horizontally at 100gpm from a 2in diameter pipe to a 1in diameter pipe. if the pressure is 10 psi at

  Find the z score values that separate

For a normal distribution, find the z score values that separate

  What would be the effect on the calculated value

what would be the effect on the calculated value of the vane efficiency for mass of jockey in error by 0.001 measurements.

  The convective heat transfer coefficient between the outer

on a cold winters day it is 30degf outside. yet the temperature of the outside surface of the mechanical engineering

  There are two connected spur gears attached to a fixed

there are two connected spur gears attached to a fixed board at points a and b. the assumptions of the system are that

  What dielectric constant must the material between the plate

A simple plate capacitor can store 6.5x10^-5 C at a potential of 10000 V. what dielectric constant must the material between the plates have if their area is 6.0x10^-5 m2 and they are 0.16 mm apart?

  An 8-kg plunger is released from rest in the position shown

an 8-kg plunger is released from rest in the position shown and is stopped by two nested springs the constant of the

  Determine the largest allowable square cross

Determine the largest allowable square cross section of a steel shaft of length 6 m if the maximum shearing stress is not to exceed 135 MPa

  Single stroke positive displacement pump

Design and construction of a modified single stroke positive displacement pump

  Plot the shear-force and bending-moment diagrams

Plot the shear-force and bending-moment diagrams for the beam and derive equations for the shear force V and the bending moment M for any location in the beam

  If the angle is big there must be a lot of tension thus as

in the bird-on-a-wire group work example how do you expect the angle and tension to be related? remember that this is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd