Determine the normal depth and critical depth in a trapezoid

Assignment Help Civil Engineering
Reference no: EM13542352

Determine the normal depth and critical depth in a trapezoidal channel with a bottom width of 12.5 m, side slopes of 2:1, and a bed slope of 0.003 m/m. The Manning’s n value is 0.022 and the discharge is 75 m3/s. Is the slope steep or mild? Repeat for n=0.012. Did the critical depth change? Why or why not?

Reference no: EM13542352

Questions Cloud

Compute the required weight of the coarse : A concrete mix with a 3 inch slump, w/c (water content) ratio of 0.50, and sand with a fineness modulus of 2.4 contrains 1700 lb/cubic yard of coarse aggregate. Compute the required weight of the coarse
What are the measures adopted to enhance sufficient : In incremental launching method of bridge construction, what are the measures adopted to enhance sufficient resistance of the superstructure during the launching process?
Why is a length of about 1.25l bridge segment is constructed : In the construction of a two-span bridge (span length = L) by using span-by-span construction, why is a length of about 1.25L bridge segment is constructed in the first phase of construction?
What do you think is the best ratio of b/y to use in your : A canal of rectangular cross-section and an n=0.030 is to be laid on a slope of 0.002 and is to carry a discharge of 30 m3/s. Calculate the cross-sectional area required for the channel to carry this flow based on the norma
Determine the normal depth and critical depth in a trapezoid : Determine the normal depth and critical depth in a trapezoidal channel with a bottom width of 12.5 m, side slopes of 2:1, and a bed slope of 0.003 m/m.
Calculate the depth of water at each end of the tank : A rectangular tank 2.0m wide, 4m long, and 2m deep contains water to a depth of 1.0m It is accelerated horizontally at 3m/s^2 in the x direction.
Water is transferred at a rate of 2.1cfs from reservior : Water is transferred at a rate of 2.1cfs from an upper reservoir to a lower reservoir by a concrete pipe 3000ft long. The difference in water level is 60ft. Determine the size of pipe for a water temperature of 60 degrees Fahrenheit. Apply The Darcy-..
At what depth of flow does the vehicle begin to move : You are in charge of evaluating the safety (hazard) of a low water crossing. Traffic surveys show that the "Aaverage"vehicle using the crossing is semi-rectangular in shape (10 ft long, 5 ft wide, and 4.0 ft high - not including the distance from the..
Estimate the required stack height for wind speeds of 4 : A plant is to be constructed that will emit 3.5 metric tons of hydrogen sulfide per day. One of the design criteria is that the concentration 1 km downwind from the stack

Reviews

Write a Review

Civil Engineering Questions & Answers

  How long would figure soil will take to reach contamination

The local engineer concludes that, since the oil must have been destroyed by the soil microorganisms at a rate of 20 mg/kg each year, in one more year the site will be free of all contamination. a. Is this a good assumption

  Estimate daily evaporation from a lake using penmans formula

Estimate daily evaporation from a lake (cm/day) using Penman's (combined) formula, given the following information: average air temperature is 28 oC, average water temperature is 15 oC, average wind speed at 8m height is 20 Km/hr

  Derive the expression for the hydraulic radius rh of a pipe

A sprinkler system uses an outdoor reservoir at El 50. A fire pump moves Q = 3 ft^3/sec through a 1.0' dia pipe 300' long to an 8" dia main at El 200. To distribute water to sprinklers, a pressure head at the pipe junction hp =100' is required.

  What is the fluid velocity in the pipe in feet per second

Water enters a pipe at 100 psig and 70 degrees F. The density of water under these conditions is 62.3 lbm/ft^3. The pipe has an inside diameter of 4.5 inches. The mass flow rate of the water is measured to be 7500 lbm/hr.

  Estimate the weight of concrete in four-lane highway segment

Estimate the weight of concrete in a four-lane highway segment that begins as a 3% grade climb from 1000 feet altitude to 4000 feet and then a 6% downgrade to 2500 feet

  Determine the total dead load

determine the total dead load, per foot of length, each beam must support.

  Determine the final velocity of each car

The coefficient ofrestitution between each car is 0.8 . Determine the final velocityof each car, after all impacts, assuming (a) cars A and C hit Car Bat the same time, (b) car A hits car B before car C does.

  Find how many dimensionless parameters govern this problem

The flowrate Q over a rectangular sharp crested weir depends on the width of the notch b, the head on the weir H, and the acceleration due to gravity g.

  Calculate how many lbs of co2 are produced per gallon

Diesel fuel has an average chemical formula of C12H23 and a density of 6.45 lb/gal. Calculate how many lbs of CO2 are produced per gallon of diesel burned (assume complete combustion).

  Conclude that the mean cost of the new method is less

It is thought that a new process for producing a certain chemical may be cheaper than the currently used process. Each process was run 6 times, and the cost of producing 100-L of the chemical was determined each time.

  The block has a mass of 150 kg and rests on a surface for

the block has a mass of 150 kg and rests on a surface for which the coefficients of static and kinetic friction are 0.5

  Determine the concentration of fe3+ in pure water

Give a few examples of movable bridge designs, that build with a certain robotics toolkit (VEX) kit. Specify the dimensions of the bridge design and the materials needed to build it from a VEX kit.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd