Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The composite shaft is made of a steel sleeve, which is bonded to a brass core. The outer diameters of the two parts are d1 = 40 mm for the brass core and d2 = 50 mm for the steel sleeve. The shear moduli of elasticity are Gb = 36 GPa for the brass and Gs = 80 GPa for the steel. Assuming that the allowable shear stresses in the brass and steel are fb = 48 MPa and fs = 80 MPa, respectively, determine the maximum permissible torque Tmax that may be applied to the shaft without any material failure. The torques are applied each at the end of the shaft opposite directions.
The compound beam is fixed at A and supported by a rocker at B and C. There are hinges (pins) at D and E. Determine the reactions at the supports.
Calculate the percipitable water (mm) in a 10-km high standard atmoshperic column if the surface conditions are temperature=20 degrees C, pressure=101.3 kPa and the laspe rate is 6.5 degrees C/km.
How many tons of asphalt concrete will be required to overlay a 3-mile-long, 24-ft.-wide road with 2.5 in. of wearing course asphalt concrete that has a density of 146.3 pcf
What does under-reinforced mean Which is desirable and why How would your Moment-Curvature plot be affected if the amount of tension steel was doubled How would your Moment-Curvature plot from part a be affected if compression steel was added to the..
The chemical 1,4-dichlorobenzene (1,4-DCB) is sometimes used as a disinfectant in public lavatories. At 20°C (68°F) the vapor pressure is 5.3 × 10-4 atm. (a) What would be the maximum concentration in the air in units of g/m3
What steps must be taken to set up a partnership? How can a partnership be dissolved?
Below a discharge from a wasterwater treament plant , an 8.6km stream has a reoxygenation constant of .4 d^-1, a velocity of .15m/s, a dissolved oxygen concentration of 6mg/L, and an ultimate demand of 25mg/L.
Straight pipe, pump head=100 ft, pipe diameter=4inches, velocity is 10 ft/sec, no elevation changes. Water at 20C. What is the length of the smooth pipe
A loose, uncompacted sand fill 6 ft in depth has a relative density of 40%. Laboratory tests indicated that the minimum void ratios of the sand are 0.46 and 0.90, respectively. The specific gravity of solids of the sand is 2.65.
Additional cost at the end of year 1 = $50,000. Benefit at the end of year 1 = $0. Annual benefits at the end of Years 2-10 = $20,000. Interest Rate = 7%. Conventionally B/C ratio and wheter the project is economically stable.
50 kmol per hour of air is compressed from p1 = 1.2 bar to P2 = 6.0 bar in a steady-flow compressor. Delivered mechanical power is 98.8KW. Temperature and velocities are: T1= 300K T2= 520K u1= 10m s^-1 u2= 3.5m s^-1
A reservoir discharge into a 60-inch concrete pipe (rough surface) that discharges freely. what is the pressure in the pipe at point A consider friction, but neglect minor losses.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd