Determine the mass of the air-initial temperature of the air

Assignment Help Mechanical Engineering
Reference no: EM13708182

Air exerts a pressure of 900KPa within a 0.45 cubic meter container of fixed volume. It is cooled such that the pressure falls to 3.25bar. The temperature of the air is then measured and was found to be 285C. Determine the mass of the air, the initial temperature of the air, the amount of heat transferred during this process.

Reference no: EM13708182

Previous Q& A

  Determine power developed by the turbine

Air enters a gas turbine with a velocity of 165m/s and a specific enthalphy of 2800KJ/kg and leaves with a velocity of 135m/s and specific enthalpy of 2175KJ/kg. The heat lost to the surrounding turbine is 32.5KJ/kg. Determine power developed by the ..

  Fundamentals of fluid mechanics

Liquid water in a pumped flow system experiences varying pressures as it circulates through the system. One concern in designing any such system is to ensure that cavitation does not occur. If the water temperature during operation of a particular sy..

  Water is in a closed rigid container with a volume

Five kg of water is in a closed rigid container with a volume of 0.3935 m3 and a pressure of 5.0 MPa. Draw and label the states and process on a P-v diagram and determine the amount of heat removed and work done when the pressure is reduced to 1.5 MP..

  Device undergoes a constant temperature process

Water as a saturated vapor at 600 °F is contained in a piston-cylinder device that has an initial volume of 30 ft3. The device undergoes a constant temperature process, until the water reaches the saturated liquid condition. Draw and label the state..

  Nitrogen in a piston-cylinder assembly

Nitrogen in a piston-cylinder assembly undergoes a polytropic expansion process. Initially, nitrogen is at 125 C and 144 kPa. Then it is expanded to a state of 102 kPa and 90 C. determine the heat transfer and work for the process considering no chan..

  Calculate the area of the hole in the tube

A slow leak develops in an inner tube (volume, 0.5 ft3, temperature, 600F), wherein it takes 4 hours for the pressure to decrease from 30 to 25 psig. The mass flow rate of air per second under the conditions is given by 0.68pA/(RT)0.5, where the unit..

  Strength and ductility of a crystalline material

Explain how you would expect the strength and ductility of a crystalline material to change as the ASTM Grain size number change from 14 to 3.

  Evaluate the concentration of vacancies in copper

Evaluate the concentration of vacancies in copper at 650C temperature. What temperature will be needed to heat treat copper such that the concentration of vacancies produced will be 1000 times more than the equilibrium concentration of vacancies at s..

  Air at standard temperature and pressure flows

Air at standard temperature and pressure flows through a horizontal galvanized iron pipe at a rate of 4.0 ft3/s. The pressure drop must not exceed 0.75 psi per 100 ft of pipe (and naturally we want to design the most economic pipe). What diameter sho..

  What is the composition-in weight percent and atom percent

What is the composition, in weight percent and atom percent, of an alloy that contains 105.0 kg iron, 20.3 kg of aluminium, and 2.0 kg of copper?

Reviews

Write a Review

 

Similar Q& A

  Calculate the mole fractions dry basis and the ppm parts

the ultimate analysis of a no.4 fuel oil is 86.47 wt carbons. 11.65 hydrogen 1.35 sulfur and the balance noncombustible

  Determine the moment of the force about point b

A 90N force is applied to control rod AB as shown. Knowing the length of the rod is 225mm, determine the moment of the force about point B by resolving the force into components along AB and in direction perpendicular to AB?

  Determine the dimensions of the lowest cost container

design an outside storage facility for methane gas ch4. 110 kg is the maximum mass of methane to be stored at this

  Calculate the pressure drop

The total hot water flow rate is 10 gal/min which is equally divided among 16 plates. The average temperature of hot water is 80C. Calculate the pressure drop.

  Determine the speed of the block at the instant

If the truck starts from rest when xD is zero, and moves forward with a constant acceleration of aD = 5 m/s2, determine the speed of the block at the instant xD = 3 m.

  A jet is coming out of a dive and a sensor in the pilots

a jet is coming out of a dive and a sensor in the pilots seat measures a force 800lbs for a pilot whose weight is

  A rigid container is separated into 2 compartments by a

a rigid container is separated into 2 compartments by a very thin solid membrane. one side initially holds 2 m3 of air

  Knowing that p starts from rest and its speed increases at

a robot arm moves so that p travels in a circle about point b which is not moving. knowing that p starts from rest and

  A long 10 cm square copper bar is bounded by 260c gas flows

a long 10 cm square copper bar is bounded by 260c gas flows on two opposing sides. these flows impose heat transfer

  A steam power plant operates on the ideal reheat rankine

a steam power plant operates on the ideal reheat rankine cycle. steam enters the high-pressure turbine at 8 mpa and 500

  Air is compressed in a piston-cylinder device from 90 kpa

air is compressed in a piston-cylinder device from 90 kpa and 22 deg celsius to 900 kpa in a reversible adiabatic

  For an infiltration rate of 09 air changes per hour ach a

for an infiltration rate of 0.9 air changes per hour ach. a building 20m long 13m wide and 3m high is kept at 24

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd