Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A turbine extracts energy from water flowing through a 11-cm-diameter pipe at a pressure of 700 kPa with an average velocity of 11 m/s. If the turbine is 90 percent efficient, how much energy can be produced if the water is emitted from the turbine to the atmosphere through a 19-cm-diameter pipe?
1750g of air performs an expansion work of 3100kJ on the surrounding as it expands isothermally to a pressure of 63000kPa ad a volume of 0.065 cubic meters. Determine the temperature of the air and the initial volume.
In a polytropic process, a fluid is compressed to 2.75 times its initial pressure, whereas its temperature becomes1.65 times. What is the fluids index of expansion, n? 1.2kg of Air at a pressure of 2.15MPa and a temperature of 585K, undergoes a rever..
Air exerts a pressure of 900KPa within a 0.45 cubic meter container of fixed volume. It is cooled such that the pressure falls to 3.25bar. The temperature of the air is then measured and was found to be 285C. Determine the mass of the air, the initia..
Air enters a gas turbine with a velocity of 165m/s and a specific enthalphy of 2800KJ/kg and leaves with a velocity of 135m/s and specific enthalpy of 2175KJ/kg. The heat lost to the surrounding turbine is 32.5KJ/kg. Determine power developed by the ..
Liquid water in a pumped flow system experiences varying pressures as it circulates through the system. One concern in designing any such system is to ensure that cavitation does not occur. If the water temperature during operation of a particular sy..
Five kg of water is in a closed rigid container with a volume of 0.3935 m3 and a pressure of 5.0 MPa. Draw and label the states and process on a P-v diagram and determine the amount of heat removed and work done when the pressure is reduced to 1.5 MP..
Water as a saturated vapor at 600 °F is contained in a piston-cylinder device that has an initial volume of 30 ft3. The device undergoes a constant temperature process, until the water reaches the saturated liquid condition. Draw and label the state..
Nitrogen in a piston-cylinder assembly undergoes a polytropic expansion process. Initially, nitrogen is at 125 C and 144 kPa. Then it is expanded to a state of 102 kPa and 90 C. determine the heat transfer and work for the process considering no chan..
A slow leak develops in an inner tube (volume, 0.5 ft3, temperature, 600F), wherein it takes 4 hours for the pressure to decrease from 30 to 25 psig. The mass flow rate of air per second under the conditions is given by 0.68pA/(RT)0.5, where the unit..
Explain how you would expect the strength and ductility of a crystalline material to change as the ASTM Grain size number change from 14 to 3.
a power plant produces a flue gas with a mass flow rate of 2 million pounds per hour. of that 150000 lbhr is water
three seconds after a polisher is started from rest small tufts of fleece from along the circumference of the
water flows at 50oc inside a 2.5-cm-inside-diameter tube such that hi 3500 wm2 oc. the tube has a wall thickness of 0.8
Discuss any of your actions and/or thought processes
Determine the resulting stress equations for σx, σy and τxy given the Airy's stress function ? = a1x^4 + a2(x^3)y + a3(x^2)(y^2) + a4x(y^3) + a5(y^4), where ai are constants. Also determine, if any, the restrictions between constants.
a 5.70kg block hangs from a spring with spring constant 1900nm . the block is pulled down 6.80 cm from the equilibrium
the following data were obtained in a resin burn-off test of an e-glass-polyester sample weight of an crucible
a centrifuge is used to remove solids from a 14.0 ppg mud using 8.33 ppg water. the mud and water enter the centrifuge
consider an ideal simple gas turbine cycle. for a net power output of 10000 horse power an inlet air temperature of
the solid a-36 steel shaft has a diameter of 0.75 inches. if it is subjected to the torques shown determine the max
a particular system obeys the relation uau-2expsr n moles of this substance initially at temperature to and pressure po
Lawn mower engines normally have finned surfaces directly attached to the engine block, with no radiator, in order to achieve the required cooling. Why might the cooling strategies be different in these two applications?
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: info@expertsmind.com
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd