Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
At one section in an air distribution system, air at 14.7 psi and 100degree F has a velocity of 1200 ft/min a and the duct is 12 in x12 in square. At another section the duct is round with a diameter of 18 inches and the velocity is 900 ft/min. Calculate: a) the density of the air in the round section. b) The weight flow rate of air in lb/hr
A rock weighs 90.8 N in air and 45 N when completely submerged in water. Determine the specific volume of the rock in m3/kg
A turbine extracts energy from water flowing through a 11-cm-diameter pipe at a pressure of 700 kPa with an average velocity of 11 m/s. If the turbine is 90 percent efficient, how much energy can be produced if the water is emitted from the turbine t..
1750g of air performs an expansion work of 3100kJ on the surrounding as it expands isothermally to a pressure of 63000kPa ad a volume of 0.065 cubic meters. Determine the temperature of the air and the initial volume.
In a polytropic process, a fluid is compressed to 2.75 times its initial pressure, whereas its temperature becomes1.65 times. What is the fluids index of expansion, n? 1.2kg of Air at a pressure of 2.15MPa and a temperature of 585K, undergoes a rever..
Air exerts a pressure of 900KPa within a 0.45 cubic meter container of fixed volume. It is cooled such that the pressure falls to 3.25bar. The temperature of the air is then measured and was found to be 285C. Determine the mass of the air, the initia..
Air enters a gas turbine with a velocity of 165m/s and a specific enthalphy of 2800KJ/kg and leaves with a velocity of 135m/s and specific enthalpy of 2175KJ/kg. The heat lost to the surrounding turbine is 32.5KJ/kg. Determine power developed by the ..
Liquid water in a pumped flow system experiences varying pressures as it circulates through the system. One concern in designing any such system is to ensure that cavitation does not occur. If the water temperature during operation of a particular sy..
Five kg of water is in a closed rigid container with a volume of 0.3935 m3 and a pressure of 5.0 MPa. Draw and label the states and process on a P-v diagram and determine the amount of heat removed and work done when the pressure is reduced to 1.5 MP..
Water as a saturated vapor at 600 °F is contained in a piston-cylinder device that has an initial volume of 30 ft3. The device undergoes a constant temperature process, until the water reaches the saturated liquid condition. Draw and label the state..
Nitrogen in a piston-cylinder assembly undergoes a polytropic expansion process. Initially, nitrogen is at 125 C and 144 kPa. Then it is expanded to a state of 102 kPa and 90 C. determine the heat transfer and work for the process considering no chan..
conventional ceramics have a fracture toughness of about 5 while advanced ceramics may have 20. determine1 how larger
an open feedwater hearter operating at steady state accepts superheated steam at 500kpa and 200degc and mixes the
consider a steam rankine cycle with superheat. the maximum temperature and pressure are 540 c and 60 bar and the
a 0.2 m3 tank containing helium at bar and 22 c will be used to supply 4.5 moles per minute of helium at atmospheric
water at 24 degree c flows at 0.8 ms in a smooth 1.5 cm i.d. tube that is kept at 27 degree c. the system is extremely
hydrogen gas at 35ordmc and unknown pressure state 1 enters a steady insulated system which has no work interaction
Examples of materials that have directional properties as a single crystal but are isotropic in their polycrystalline form.
a 2-kg ball b is traveling horizontally at 3 ms when it strikes 2-kg ball a. ball a is initially at rest and is
steam expands in a turbine steadily at a rate of 36048 kgh entering at 8 mpa and 600degc and leaving at 20 kpa as a
A robot arm carrying a 2.75-lb package is moving in a horizontal circle at 4 miles/hr. The arm is gradually shortened for the first 0.11 s of its motion, changing the radius of the circle. The maximum acceleration the package can withstand without da..
a helix compression spring is manufactured using the following parametersod1.00id.790wire dia 0.105fo 40.49 lbf
write a reflective assessment of how you rate yourself against these competencies and Describe the main learning outcomes that this course and the EWB project have generated for you over the semester. Have any of these learning outcomes been a ..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: info@expertsmind.com
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd