Determine the magnitude of the velocity and acceleration

Assignment Help Civil Engineering
Reference no: EM13318100

The vertical-axis wind turbine consists of two blades that have a parabolic shape. If the blades are originally at rest and begin to turn with a constant angular acceleration of ac = 0.5 rad/s^2, determine the magnitude of the velocity and acceleration of points A and B on the blade when t = 4s.

the verticle axis has two prabolic wings that connect at the top and bottow that are 180 degrees apart (in same plane) Point A is located in the middle of the verticle axis and has a radius of 20ft. Point B is located in the upper half of the verticle axis and has a radius of 10ft from the verticle axis.

Reference no: EM13318100

Questions Cloud

Determine the moment of inertia and the radius of gyration : Determine the moment of inertia and the radius of gyration of the shaded area with respect to the x axis.
What is the total power that the battery supplies : A coil has an inductance of 0.45 H and a resistance of 42 ohms. The coil is connected to a 5.6 V ideal battery. What is the total power that the battery supplies
Determine the system curve for the pump system : The entrance is square edged, and the elbows are 90o. There is a fully opened gate valve on the suction side and the discharge side, and there is a swing type check valve on the discharge side. Determine the system curve for the pump system.
At what rate is the energy being dissipated : A coil has an inductance of 0.45 H and a resistance of 42 ohms. The coil is connected to a 5.6 V ideal battery. At what rate is the energy being dissipated
Determine the magnitude of the velocity and acceleration : If the blades are originally at rest and begin to turn with a constant angular acceleration of ac = 0.5 rad/s^2, determine the magnitude of the velocity and acceleration of points A and B on the blade when t = 4s.
Which is the change in the electric potential energy : An electron and a proton are initially very far apart (effectively an infinite distance apart). which is the change in the electric potential energy
Calculate the min velocity of flow in ft per sec of water : Calculate the minimum velocity of flow in ft/sec and m/sec of water at 160 degrees F in a 2 in. dia pipe for which the flow is turbulent
What trends in the environmental forces : What trends in the environmental forces (social, economic, technological, competitive, and regulatory) work for and/or work against Rollerblade's potential growth in the 21st century?
Find final temperature of steam and amount of mass transfer : A valve is now opened and steam at 1Mpa at 473 K is allowed to enter the cylinder until the volume inside increases to 0.04m^3 . Determine the final temperature of the steam and the amount of mass transfer

Reviews

Write a Review

Civil Engineering Questions & Answers

  What force is required to hold in equilibrium under mercury

A cube has side dimensions of 18.00 in. It is made of steel having a specific weight of 491 pcf. What force is required to hold it in equilibrium under mercury

  How long must radioisotope be held to meet allowable charge

A hospital waste containing 0.7µCi/L of 32P is to be disposed of. How long must the radioisotope be held to meet the allowable discharge activity

  Find invert of stilling basin require to form hydraulic jump

The subcritical water level in the channel downstream from the stilling basin is at an elevation of 100 feet above the datum. assume no energy loss over the spillway, determine the invert of the stilling basin required to form a hydraulic jump in ..

  Total mass-quality of steam-specific volume

Find the total mass, quality of steam, specific volume, specific enthalpy, and specific internal energy.

  How many of the incinerators in chicago meet the standard

Stack gas samples were collected from a sample of 50 incinerators in Chicago. Of the 50 samples, only 18 met an environmental standard for the concentration of a hazardous compound. Can it be concluded that fewer than half of the incinerators in C..

  Determine the maximum shear stress for the shape

The shape below has a cut along the entire length of the member thus making it an open section. The uniform thickness is 0.125in. Determine the maximum shear stress for the shape. Compare the stress for this open shape to a shape without a cut.

  Find allowable load p that can be supported by connection

A steel bar is attached to a wood support beam with four 20 mm diameter lag screws. The steel bar is 75-mm-wide by 6-mm-thick. For the steel bar, the yield strength is 260 MPa and the ultimate bearing strength is 350 MPa.

  Calculate entropy increase assuming constant specific heat

A paddle wheel, inserted inserted into the volume, does 720 KJ of work on the air. If the volume is 2 cubic meters, calculate the entropy increase assuming constant specific heats.

  What ph is required to acheive aluminum ion concentration

Aluminum ion (Al3+) is present in an industrial wastewater at 3 mg/L. The treatment facility wants to precipitate out the aluminum until there is only 0.2 mg/L remaining. What pH is required to acheive this aluminum ion concentration

  Show how kh and kow can be used to describe koa

Show how Kh, and Kow can be used to describe Koa. You must show how the concentration units for all equilibrium distribution ratios either cancel or remain to give the final value for Koa. Octonal-air partitioning coefficient (Koa = C(octanol)/C(a..

  How many days per year does the equipment need to be used

If a new piece of equipment costs $40,000.00 to purchase and it has a benfit of $500 per day. How many days per year does the equipment need to be used in order to be worth purchasing (breaking even)

  What are rotational velocity in rpm and linear velocities

One form of which consists of three equal weights joined by equal length ropes. The gaucho holds on to one weight spinning the bolas overhead. When the bolas is cast the weights cause the configuration to change

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd