Determine the final volume of the gas in

Assignment Help Civil Engineering
Reference no: EM13563878

1.Three feet of flash boards were placed on the top of a small diversion dam. The pipes holding the boards were placed 10 ft apart across the dam. There were 20 pipes and each one was designed to fail under a bending moment of 1625 ft-lb how deep will the water be on the flash boards when failure occurs? Assume hydrostatic pressure distribution on the flash boards.

2.two steel spheres 100mm in diameter. Compute gravitational force and the force of mutual attraction F in newtons. the specific weight of steel is 0.284 lb/in^3

3.A piston-cylinder assembly containing 1/4 kg of a gas undergoes a constant pressure process at 5 bar beginning with a specific volume of 20 m^3/kg. for the gas in the system the work is -15 kj. determine the final volume of the gas in m^3

4.At what water depth would a semi-diurnal tidal wave (T = 12.4 hrs) cease being a shallow water wave and become a transitional wave?

Reference no: EM13563878

Questions Cloud

How many ions of each type are there per unit cell : A particular unit cell is cubic with ions of type A located at the corners and facecenters of the unit cell and ions of type B located at the midpoint of each edge of the cube and at the body centered position.
Determine the average normal stress and average shear stress : A wood board with a 2in. by 4in. cross section is subjected to a tensile load of 100 lb. Determine the average normal stress and average shear stress developed in the wood fibers that are oriented at 30 degrees with the axis of the board.
What is actually measured at the rec5 : There are two methods for determining the range from the SV to the REC in GPS. Code (C/A and P) and waves (L1 and L2) discuss two elements of GPS signals as they relate to each method. choose from the list of elements shown below.1.determination of t..
Sketch the processes on p-v coordinates and evaluate the : Carbon dioxide gas contained within a piston-cylinder assembly undergoes three processes in series. Sketch the processes on P-V coordinates and evaluate the work for each process in kJ.
Determine the final volume of the gas in : A piston-cylinder assembly containing 1/4 kg of a gas undergoes a constant pressure process at 5 bar beginning with a specific volume of 20 m^3/kg. for the gas in the system the work is -15 kj. determine the final volume of the gas in m^3
Calculate the volumetric flow rate when the meter reads : An orifice meter was calibrated for dry air at T=90 F and P=1.3 atm. The calibration data are as follow:
How much contact time would be reuired for inactivating : How much contact time would be reuired for inactivating Giardia cysts using the following chemicals at the concentrations and temperatures stated: a. Chlorine Dioxide, 23C, 1.0 mg/L b. Chlorine, 12C, 1.6 mg/L c. Ozone, 10C, 5 mg/L d. Chloramines, 20C..
Compare your results with the true value of the derivative : We know that the molar concentration and volume of a solution is the sum of the product of the molar concentration and volume of each solution component before mixing
Write the mass balance equation for a completely mixed lake : Write the mass balance equation for a completely mixed lake with an impulse input of mass,M, added at time t=0. Assume the lake is of constant volume, V, with continuous outflow, Q, and a conservative substance

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what external force is required to hold the bend

A pipe 1ft in diameter bends through an angle of 135 degrees. The velocity of flow of gasoline ( S = 0.8) is 20ft/s and the pressure is 10psig in the bend. What external force is required to hold the bend against the action of the gasoline

  Draw circle and put line with angle

Draw circle and put line with angle inside the circle that reflected in it. Make sure the measurement is punctual for each one. Angels required are 20-40-60 degrees. that means you have to draw three circles.

  What is the steady state emission rate of co by automobiles

The maximum eight-hour average concentration of carbon monoxide (CO) in an urban area is measured to be 17 ppm. The NAAQS is 9 ppmv (equivalent to 10.3 mg/m^3 estimated at P = 1 atm and T=298.25°K).

  Calculate the engineering stress for the bar

Calculate the following for the bar:a) engineering stress at 0.001 (0.1%) strain, b) elongation, c) Young's modulus, d) final diameter of the bar Note: Poisson's ratio is 0.31 for 4140 steel, e) true stress, f) true strain.

  How high can that person climb the ladder before the slip

A ladder is supported by a horizontal floor and a vertical wall. Is 15 feet long and weighs 50 lbs, with the weight concentrated at its midlength. The ladder supports a person weighing 180 lbs.

  Determine the horizontal and vertical components

A 2ft diameter hemispherical plexiglass "bubble is to be used as a special window on the side of an above-ground swimming pool.

  Determine the entrance losses

A 40 cm diameter well has been constructed in a water-table aquifer. A pump capable of continuous discharge at 600 m3/day has been installed to test the well. Observation wells are located 10 meter and 50 meters from the pumped well. After pumping co..

  Determine the radius r of the inner core of the shaft that

For a given hypothetical flow, the velocity from time t=0 to t=5s was u=3m/s, v=3m/s. then from time t=5s to t=10s, the velocity was u=2m/s, v=2m/s. A dye streak was started at a point in the flow

  Compute the sorbed concentration in equilibrium with the

If the pH of the water is raised to 8.5, what is the equilibrium concentration of the chromium (III) in moles/L? (d) What weight (in pounds) of precipitate is formed if groundwater containing 19,000 mg/L chromium is treated as described in part (c) a..

  Estimate the median and 90th percentile load

Estimate the median and 90th percentile load of SS contained in the runoff. Note: COV = coefficient of variance

  Municipal utility-considering two large-scale conduits

A big municipal utility district is considering two large-scale conduits. The first includes construction of a steel pipeline at a cost of $200 million.

  Compute magnitude of the load that is necessary to produce

A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa, and an elastic modulus of 105 GPa. A cylindrical specimen of this alloy 12.7 mm in diameter and 250 mm long is stressed in tension and found to elongate 7.6 mm.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd