Determine the diameter of commercial steel pipe required

Assignment Help Civil Engineering
Reference no: EM13555162

1.World population 10,000 years ago has been estimated at about 5 million. what exponential rate of growth would have resulaed in the population in 1850 , which is estimated at 1 billion ? had that rate continued , would the population have been in the year 2000?

2.Determine the diameter of commercial steel pipe required to convey a minimum of 300 cfs of water at 60 deg F with a head loss of 1.2 ft per 1000 ft of pipe. Assume pipes are available in the following nominal diameters (inches): 2, 4, 6, 8, 12, 14, 16, 18, 20, 22, 24, 30, 36, 42, 48, 54, 60, 66, 72.

Reference no: EM13555162

Questions Cloud

Determine the shear stress at each wall and the maximum : Sketch and identify the Tresca (maximum shear stress) and von Mises (maximum distortion energy) failure criteria in two-dimensional principal stress space (i.e., ?2 vs. ?1) for the above material.
What are the northing and easting coordinates for station b : The coordinates for station A are 1023.34 N and 988.56 E. What are the northing and easting coordinates for station B that is located 40 feet due east of A, and 22.32 feet due south of A
Find the maximum allowable tensile force : A 4-cm- diameter rod of aluminum 7075-T6 is to subjected to an axial tensile force such that the factor of safety based on the yield stress on 1.75. Find the maximum allowable tensile force. The yield stress of the aluminum 7075-T6 is o-y= 500MPa.
Use the doubling time approximation to estimate : Use the doubling time approximation (3.5) to estimate the exponential rate of growth that would produce those numbers. Use the exponential growth equation (3.6) to find the growth rate
Determine the diameter of commercial steel pipe required : World population 10,000 years ago has been estimated at about 5 million. what exponential rate of growth would have resulaed in the population in 1850 , which is estimated at 1 billion ? had that rate continued , would the population have been in the..
What is the resulting solids concentration : Raw primary sludge at a solids concentraion of 4% is mixed with waste activated sludge at a solids concentration of .5%. The flows are 20 and 24 gal/min respectively.
What fraction of the flue gas stream would need to be bypass : An electrostatic precipitator for a coal-fired power plant has an overall particulate recovery of 95%. The company engineer decides that this is too good, that it is not necessary to be this efficient
What is the pressure difference measured by the manometer : The "U"-tube manometer containing mercury of density 13600 kg/cubic meters is used to measure the pressure drop along a horizontal pipe.
What tensile force should be applied to the bar to maintain : Suppose that in an apparatus it is necessary to maintain precisely the cross section of a 20mm circular nickel steel bar. If this bar is heated to 200 deg Celcius

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the corrected measurement

A measurement was recorded as 171.278 m with a 30-m tape that was only 29.996 m under standard conditions. What is the corrected measurement?

  Design a curve for the highway by computing the radius

The PI is at station 250+50, the design speed is 65mi/h, and a maximum superelevation of 0.07 ft/ft is to be used. If the central angle of the curve is 38 degrees, design a curve for the highway by computing the radius and stationing of PC and PT.

  Compute 95 percent confidence intercals for b0 and b1

An article reports measurements of expansion for several concrete bridges in the area of Quebec City. Following are measurements of horizontal and vertical expansion (in parts per hundred thousand) for several locations

  Calculate the magnitude of the force supported by bearing

The uniform 25 kg plate is welded to the vertical shaft, which is supported by bearings A and B. Calculate the magnitude of the force supported by bearing B during application of the (M =) 140 N·m couple to the shaft.

  Calculate the air mass temperature at the elevation levels

A strong wind moves the air mass over a mountain range at 2,500 m. mean sea level and then the air descends to an elevation of 500 m on the leeward of the mountain.

  Determine the values of k and c

The landing gear of an airplane can be idealized as the spring-mass damper system. If the runway surface is described y(t)=y0 cos wt, determine the values of k and c that limit the amplitude of vibration of the airplane (x) to 0.1m. Assume m=2000k..

  How fast will ball c be traveling after all collisions cease

Three particles are sliding along a flat, frictionless surface. mA = 0.4 kg, mB = 0.5 kg, and mC = 0.4 kg. Before any collisions take place, vA = 15i m/s, vB = 10im/s, and vC = 5 m/s. e = 0.85 between A and B and e = 0.6 between B and C.

  Calculate the concentration of particulates in the stack

The temperature in the stack is 300 degrees F and the pressure is 725 mm Hg. If the total flow rate of gas out of the stack is 190 standard cubic meters per second, calculate the total mass emissions of particulates out of the stack in kg/day.

  What is the solids concentration of primary clarifier sludge

a 20 mgd wastewater treatment plants primary clarifier influent has 800 mg/l solids. the clarifier removes 18 percent of the solids. the sludge flow rate is 0.070 MGD. (a) what is the solids concentration of primary clarifier sludge

  Classify the jump type and calculate the energy lost

A rectangular channel of width 12 ft has an upstream slope of 0.02 ft/ft and a downstream slope of 0.0005 ft/ft. Both reaches have lengths of 500 ft. The upstream reach has a Manning's roughnes

  Find the horizontal and vertical forces exerted on the poll

What is the maximum weight that can be suspended on a 16 Kg poll, 3/5 from the end. The maximum tension of the 30 degree guy-wire is 1500 N. Find the horizontal and vertical forces exerted on the poll by the hinge.

  Which method would be most likely to have the conductivity

If an analysis is made of the hydraulic conductivity of a site using permeameter tests of core samples, slug tests of monitoring wells, and pumping tests of production wells, it is often observed that the hydraulic conductivity as measured by each..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd