Determine the daytime and nighttime voltages at every bus

Assignment Help Electrical Engineering
Reference no: EM13967736

Suppose that a new transmission line is to be added to the power system between Bus 1 and Bus 4. The line is rated at 200 MVA, and its series impedance is 0.008 + j0.064 pu. Assume that no capacitors have been added to the system, and determine the daytime and nighttime voltages at every bus. Did the new transmission line resolve the voltage problems?

Reference no: EM13967736

Questions Cloud

The aspen ridge limited partnership : The Aspen Ridge limited partnership was formed on April 1, 2009, by Mark Sullivan, its general partner, and two other limited partners when they each contributed an equal amount of cash to start the new enterprise
Discuss fully the principle of acquisitions management : Discuss fully the principle of Acquisitions Management. What is most important? What do you think will become more important over the next two decades?
One of kant''s ways of formulating : One of Kant's ways of formulating (i.e., expressing in words) the Categorical Imperative says that "one should always treat humanity, whether in oneself or in another, always as an end and never merely as a means". This is often called the "Formula o..
Identify important issue that is represented within article : The goal of this assignment is to identify the important issue that is represented within the article you select. Your task will be to share why this is an important and current issue in business and/or management.
Determine the daytime and nighttime voltages at every bus : Suppose that a new transmission line is to be added to the power system between Bus 1 and Bus 4. The line is rated at 200 MVA, and its series impedance is 0.008 + j0.064 pu. Assume that no capacitors have been added to the system, and determine t..
Calculate the heritability of religiousness : If the researcher uses Falconer's formula to calculate the heritability of religiousness without taking assortative mating into consideration, how would the heritability estimate be affected? (Would it be inflated? Deflated? Would it be accurate?)
Healthcare professionals often work rotating shifts : Healthcare professionals often work rotating shifts. In your own words, why is this problematic? What are the psychological, social, and physiological challenges related to rotating shifts? Consider sleep deprivation, high levels of stress, or side e..
Define a set of capacitors at various busses in the system : Suppose that the power system is operating under typical daytime loads, and the transmission line between Bus 4 and Bus 5 open circuits. What happens to the voltages on each bus now? Are any of the transmission lines overloaded?
New minimum cycle time : Because two of the process steps can now run in parallel (gathering the food and taking the money), what is the new minimum cycle time? What is the longest cycle time? What potential problems could arise by splitting the process across two individ..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Design a circuit to control taillights of ford thunderbird

The state machine has two inputsignals, LEFT and RIGHT, that carry the driver's request fora left turn or a right turn. It also has anemergency flasher input, HAZ, that requires the tail lights to beoperating in hazard mode - all six lights flashi..

  Determine what is the initial buffering delay

Consider the simple model for HTTP streaming. Suppose the server sends bits at a constant rate of 2 Mbps and playback begins when 8 million bits have been received. What is the initial buffering delay

  Calculate the resistance change resulting from a strain

A strain gauge has a GF=2.14 and a nominal resistance of 120 Ohm . Calculate the resistance change resulting from a strain of 144µin / in .

  Describe time-domain sequences for unity-amplitude

Recall that for discrete sequences the ts sample period (the time period between samples) is the reciprocal of the sample frequency fs. Write the equations, describing time-domain sequences for unity-amplitude cosine waves

  Evaluate the pros and cons of using the snr and signal

Which of these metrics are dependent on link conditions: CINR, SNR, or BER Evaluate the pros and cons of using the SNR and signal - to - interference - noise ratio ( SINR ) for estimating signal quality versus using the absolute value of the signa..

  Find out how to use the solve function to solve for va

To analyze electric circuits, it is often necessary to solve simultaneous equations. To find the voltages Va, Vb, and Vc at nodes a, b, and c, the equations are 2(Va-Vb) + 5(Va-Vc) - e^(-t) =0 2(Vb-Vc) + 2Vb + 3(Vb-Vc) =0

  What is total impedance of series circuit having resisor

What will be the total impedance of a series circuit having a resistor of 100 ohms, an inductor of 200 ohms reactance, and a capacitor of 300 ohms reactance. Also, what will be the dissipated power when voltage source is 10sin1000t.

  Determine what is the value of source current

An input signal of 10V at 0o is applied to a parallel RLC circuit with resistor R = 100 , inductive reactance XL = 100 , and capacitive reactance XC = 200 . All three components are connected in parallel to the source. what is The source current.

  What is the dc output voltage due to the input-bias currents

The operational amplifier below has a specified input-bias current IIBup to 250nA and a maximal input-offset voltage VOS of ±3mV. It has a unity-gain frequency (gain-bandwidth product) of 1MHz.

  Optical waveguide-ring resonator system

You need to write a term paper based on this paper topic "Critical Coupling and Its Control in Optical Waveguide-Ring Resonator System"

  Find what is the average current drain from the battery

Suppose that we are designing a cardiac pacemaker circuit. The circuit is required to deliver pulses of 1-ms duration to the heart, which can be modeled as a 500 ohm resistance. The peak amplitude of the pulses is required to be 5 V.

  The design statistics for the actual hardware

the only things that should show up on the LCD display are the last four of your UID or "0000." The m1605.ucf file is the user constraint file that defines where the nil605.vhd I0 pins are assigned on the FPGA. Once your design is working, report ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd