Determine the current density in the dielectric

Assignment Help Chemical Engineering
Reference no: EM131194132

Lossy coaxial cable. In a coaxial cable of length L, the inner conductor is of radius a and the outer conductor of radius b and these are separated by a lossy dielectric with permittivity ε and conductivity CT. A de source, V, is connected with the positive side to the outer conductor of the cable. Neglecting edge effects determine:

(a) The electric field intensity in the dielectric.

(b) The current density in the dielectric.

(c) The total current flowing from outer to inner conductor.

(d) The resistance between the outer and inner conductors.

Reference no: EM131194132

Questions Cloud

Nursing practices use to promote patient rights : Discussion: The Nurse's Role in Promoting Patient Rights- What are some nursing practices you could use to promote patient rights and responsibilities?
Find the drift velocity of the electrons in copper : Find the drift velocity of the electrons in copper.
Create slides that reinforce and illustrate your main ideas : For the body of your presentation, cover the main points of your report. Create slides that reinforce and illustrate your main ideas. Follow basic design principles for effective slide content.
Calculate the electric field intensity inside the conductor : Drift velocity and electric field intensity in conductors. A copper conductor with conductivity σ = 5.7 X 107 S/m carries a current of 10 A. The conductor has a diameter of 2 rom.
Determine the current density in the dielectric : Lossy coaxial cable. In a coaxial cable of length L, the inner conductor is of radius a and the outer conductor of radius b and these are separated by a lossy dielectric with permittivity ε and conductivity CT. A de source, V, is connected with th..
Imagine life during postwar time : Imagine yourself living in the 1950s and 1960s.-  How would your life be different than it is today? How would it be the same?
Determine the graphical display tool : Determine the graphical display tool (e.g., Interaction Effects Chart, Scatter Chart, etc.) that you would use to present the results of the DOE that you conducted in Question 1. Provide a rationale for your response.
Type of paper clip matters : Do you think it matters what type of decisions are included in this 52%? For example, would getting the right type of paper clips be as influential a decision as deciding where to locate the business? Can you think of a situation where the type o..
Make notations on the given letter : Is this letter written using the direct order or the indirect order? Is the choice appropriate?- Make notations on the letter indicating any deletions you will make and flagging any terms or phrases that you don't like.

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Question 1a outline the provisions of occupational safety

question 1a outline the provisions of occupational safety and health act 2005 with regard to substances hazardous to

  Determine the flow rate of sodium hydroxide

Two beds are used, with one in operation and one in regeneration. If the bed is designed to be 80% loaded at the end of a 2 hour operation cycle, estimate the bed volume. Also determine the flow rate of sodium hydroxide required during the regener..

  Calculate the excitation voltage and the power angle

If the motor is operating on load with a power angle of -20°, and the excitation is adjusted so that the excitation voltage is equal in magnitude to the terminal voltage, determine the armature current and the power factor of the motor.

  Find the mean and variance of x

Each morning, Hungry Harry eats some eggs. On any given morning, the number of eggs he eats is equally likely to be 1. 2, 3, 4, 5, or 6, independent of what he has done in the past. Let X be the number of eggs that Harry eats in 10 days. Find the ..

  Determine the heat of mixing ah of sulfuric acid in water

Determine the heat of mixing AH of sulfuric acid in water and the partial specific enthalpies of H2SO4 and H2O for a solution containing 65 mass-% H2SO4 at 298.15 K (25°C)

  Effect of different chemicals on the strength of a fabric

An experiment was performed to determine the effect of four different chemicals on the strength of a fabric. These chemicals are used as part of the permanent press finishing process. Five fabric samples were selected, and a randomized complete block..

  What is the optimum operating reaction temperature

For a reversible exothermic elementary catalytic reaction of the type A B, what is the optimum operating reaction temperature at a conversion level , xa = 0.8 given- K1 = exp ( 10 -5000/T) K2 = exp ( 40 - 15000 /T) and maximum allowable temperatu..

  Calculate the molarity of each of these solutions

A 0.1025-g sample of copper metal is dissolved in 35 mL of concentrated HNO3 to form Cu2 ions and then water is added to make a total volume of 200.0 mL. (Calculate the molarity of Cu2.)

  Draw a pv graph and show this process

Draw a PV graph and show this process. Show all the relevant temperatures and pressures as well as the critical isotherm and the critical pressure.

  Find the current i1 through the 20-? resistor of the circuit

Find the current I1 through the 20-Ω resistor of the circuit of Figure P2.2.8 by both mesh and nodal analyses.

  Calculate the composition of the vapor phase in the previous

Draw a qualitative Pxy graph for this system at 100 °C. Show all the important features on the graph. The saturation pressure of nitrobenzene at 100 °C is 21 mmHg.

  Find the three highest speeds at which this linkage possible

Find the three highest speeds at which this linkage would be possible.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd