Determine how many candy bars she needs to take with

Assignment Help Civil Engineering
Reference no: EM13550408

A 68 kg woman is planning to bicycle for an hour. If she is to meet her entire energy needs while bicycling by eating 30 g chocolate candy bars, determine how many candy bars she needs to take with her. Assume that an average 68 kg adult consumes 639 Calories/hour while bicycling, and the energy content of a 20 g chocolate candy bar is 105 Calories

Reference no: EM13550408

Questions Cloud

Calculate the time average f of the total force tangent : The 1500kg car has a velocity of 30 km/h up the 10 percent grade when the driver applies more power for 8 s to bring the car up to speed of 60 km/h.
What rate of return will the person make : A person who retires at age 62 can receive Social Security benefits of $1537 per month, but by waiting for the full retirement age of 66, the person will receive $2057 per month. What rate of return will the person make
Determine the subsidence of the clay surface : Groundwater is pumped for domestic use from an unconfined aquifer. the thickness of the clay is 40%. after 10 years of pumping, the porosity is reduced to 30%. determine the subsidence of the clay surface.
What is the added mass on the roof : The Hubert H. Humphrey Metrodome in Minneapolis opened in 1982 at a cost of $55 million. To prepare for the footings, et cetera, 30.0x10^5 cubic yards of dirt were removed.
Determine how many candy bars she needs to take with : A 68 kg woman is planning to bicycle for an hour. If she is to meet her entire energy needs while bicycling by eating 30 g chocolate candy bars, determine how many candy bars she needs to take with her
Determine the effectiveness of the regenerator : A Brayton cycle with a regenerator uses air as the working fluid. The air enters the compressor at 283K and 0.1 MPa. The highest temperature in the cycle is 1073K and the pressure ratio across the compressor is 8
Determine the rate of change of density in the tire : Air at 37 psi and 60oF is being forced into a tire at a velocity of 180 ft/s through a ¼ in. diameter opening. The tire has a volume of 17 ft3. Determine the rate of change of density in the tire. (3.01 *10-5 slugs/ft3 s)
A tank with a 3m diameter has an 8 cm orifice at the bottom : A tank with a 3m diameter has an 8 cm orifice at the bottom. The tank is currently filled with water to a height of 2.5m above the orifice. If the orifice is opened.
Consider a metal single crystal oriented such that : Consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of 42.1* and 48.9*, respectively, with the tensile axis. If the critical resolved shear stress is 18.2 MPa (3000 psi)

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is p-value and find critical value of test statistic

The specification for a particular application calls for the blocks to have a mean compressive strength greater than 1350 kPa. A sample of 100 blocks is produced and tested.

  Find area of steel reinforcement required for concrete tbeam

Find the area of steel reinforcement required for a concrete T-beam for the following data; f'c = 3 ksi, fy=60 ksi,d=18 in, t= 4.5 in., bw= 10 in., bf= 36 in., 3/4" aggregate, and the section sustains a total factored bending moment 82 k-ft.

  Determine what is the rate of flow into the reservoir

Runoff from a storm flows into a reservoir with a surface area of 20.0 ha at a constant rate. The reservoir level is observed to rise at 1 mm per minute when water is being released through the dam at a rate of 10 m3 per second.

  Calculate the energy needed to bring the soil

We are digging a hole to build a building. Calculate the energy needed to bring the soil to surface level. Remember the sides of the excavation lie at 45 degrees. Else, the whole would be constantly refilling itself.

  Determine the stack-gas so2 concentration in units

The sulfur dioxide (SO2) stack-gas concentration from fossi-fuel combustion is 2 ppmv. Determine the stack-gas SO2 concentration in units of micro grams/m^3. Assume 0C and 1 atm pressure

  Determine the torque that develops in the rod

The end of a 0.75-in-diameter rod is fixed to an immovable plate as shown. The length of the rod is 18.0 in. A 50-lb weight is attached to a 16.0-in lever at the end of the Rod so that the weight is hanging perpendicular to the longitudinal axis of t..

  What percentage is this loss reduced if the provision

Water leaves a turbine at 18.5 fps and enters a tailrace having an average velocity of 1.5 fps. What is the submerged discharge head loss? By what percentage is this loss reduced if the provision of a draft tube increases the discharge flow area to s..

  How to sketch p-v diagram as the pressure is raised

The phase diagram of a typical simple substance contains three phases , liquid vapor and solid separated by boundaries . The critical point terminates the liquid-vapor transition, in water it is at Pc=220.9 bar and Tc=374 degres celcius

  Difference between labor cost and labor pro-ductivity

Determine the number of man-hours required to form the structure using data from R. S. Means or other appropriate reference. What is the difference between labor cost and labor pro-ductivity?

  Determine the moment of the 300 n force about d

A 300 N force is applied at A. Determine (a) the moment of the 300 N force about D, (b) the magnitude and sense of the horizontal force applied at C that creates the same moment about D,

  Determine the weight of the gate per meter length

The homogeneous gate shown in Fig. P2.88 consists of one quarter of a circular cylinder and is used to maintain a water depth of 4 m. That is, when the water depth exceeds 4 m, the gate opens slightly and lets the water flow under it. Determine the w..

  Find the magnitude and depth of the point of application

Find the magnitude and depth of the point of application of the force on the circular gate shown (circular gate at an angle of 60 deg.) if h(distance from top of gate to top of water)=5ft. and D(length of the gate)=4 ft.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd