Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Design an arithmetic shifter. The device should input a 4-bit value x and a 2-bit control c and output a 4-bit value representing the shifted input. If c = 00 then shift left one, if c = 01 then shift right one, if c = 10 then shift right two, and when c = 11 output x without shift.For an example of how this works, consider the possible inputs x1 = 1011 and x2 = 0111. When we shift left we fill in the 0's so that a shift of one left gives x1 = 0110 and x2 = 1110. When we shift right we fill with the sign bit, so that a shift of one right gives x1 = 1011 and x2 = 0011 and a shift of two right gives x1 = 1110 and x2 = 0001.
The frequency of a clocking signal is 10MHZ and it is used to sample serial data stream. If the data must be stable for 15ns before the leading clock edge and for 10ns after the leading clock edge, how much time is available to change the data bet..
Design a BP filter using two-integrator topology. The center frequency is to be 10kHz with a bandwidth of 2kHz. Design to obtain a voltage gain of 26dB.
An electric field of 3.10×105 is desired between two parallel plates, each of area 36.0 and separated by 0.620 of air.What charge must be on each plate?
A uniform magnetic field is applied perpendicular to the plane of a 60-turn circular coil with a radius of 6.0 cm and a resistance of 0.60 ohms. If the magnetic field increases uniformly from 0.20 T to 1.8 T in 0.20 s
Assume the acceptable deviation is +- 5.8%. Thus, a nominal rms voltage of 120 V will range from 113 to 127 V. Suppose the line to line voltage at Customer A is 13.8kV, the load at customerA consumes complex power (1.2+j1.2)x 10^6 W.
Design a circuit that will add either 1 or 2 to a 4-bit binary number N. Let the inputs N3, N2, N1, N0 represent N. The input K is a control signal. The circuit should have outputs M3, M2, M1, M0, which represent the 4-bit binary number M.
an office with several work stations has an effective area of 527 sqft (49 meters). it has decorative incandescent lighting. The lamps are 40 watt yielding an out put of 18 lm/W. An illumination of 645 lux is required for the work stations.
Which is the best alternative to buying a machine assuming an interest rate of 4% and a time span of 6 years. Compare using Present Values. A: Buy new machines for $25k. They earn $5k per year and their maintenance costs are $125 per year.
Design a 2-bit counter that, when f = 1, counts in the repeating sequence: 0, 2, 3, and when f = 0, counts in the reverse direction. Use T flip-flops. (a) Construct a state diagram or state table.
Draw a circuit diagram to show how the CT, VT and meters are connected into the load circuit. Neglecting instrument and transformer errors, calculate the load kVA and power factor if the voltmeter, ammeter and wattmeter indicate values of 200 V, 2..
Discuss why it is important to understand how interpret data from op amp datasheets. How might this skill be used when designing op amp circuits.
What is the maximum number of consecutive bits that are in error for a transmission through this channel if the data rate is 10Kbps? If the data rate is 11 Mbps?
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd