Describe the direction in which the bilayer bends

Assignment Help Civil Engineering
Reference no: EM131070025

An aluminum film, 1 urn in thickness, is deposited onto a silicon substrate which is 500 fim thick and 100 mm in diameter. The isotropic properties of

757_2a02c977-7450-489d-867c-216e577528c0.png

perature, this thin-film/substrate system is flat (i.e. zero curvature). This bilayer is now uniformly cooled by 50 °C.

(a) What is the average stress in the aluminum film?

(b) Is it tensile or compressive?

(c) Describe the direction in which the bilayer bends during the above thermal excursion.

(d) If the yield strength of the thin aluminum film is 140 MPa, what is the temperature change needed to cause plastic yielding in the aluminum film?

(e) If the thin-film/substrate system is thermally cycled between the stressfree initial temperature and some high temperature Tcycle what is the minimum value of Tcycle needed to induce fully reversed plastic flow in the entire aluminum film?

Reference no: EM131070025

Questions Cloud

Definition of the pid algorithm : A practical discussion of the function of each of the three terms (proportional, integral, derivative) and An explanation of the affects that changing each of the three tuning constants has on the resulting control response.
Proportion of total cases occurring in boys : The table below provides information on the number of students per type of residence and the number reporting illnesses consistent with the described symptoms and onset time. What is the proportion of total cases occurring in boys?
Analyze cabrera foods logistics exercise in cabrera foods : Analyze the Cabrera Foods Logistics Exercise in the Cabrera Foods handout. Identify possible solutions to Cabrera's challenges.
Difference between extrinsic and intrinsic motivation : What is the difference between extrinsic and intrinsic motivation?
Describe the direction in which the bilayer bends : If the thin-film/substrate system is thermally cycled between the stressfree initial temperature and some high temperature Tcycle what is the minimum value of Tcycle needed to induce fully reversed plastic flow in the entire aluminum film?
Overwhelming majority of the cases disposed : Jackson County judges try thousands of cases per year. In an overwhelming majority of the cases disposed, the verdict stands as rendered.
Draw conclusions from the visual data : Apply critical thinking and communication skills to draw three conclusions from the visual data presented in the article and use the conclusions drawn to make inferences about future projections based on the data.
Population proportions that possess the given characteristic : Using this data, a 95% confidence interval is constructed to estimate the difference in two population proportions that possess the given characteristic. The resulting confidence interval is:
Heteroskedasticity and autocorrelation problems : We will ignore any heteroskedasticity and autocorrelation problems in the remainder of this question. However, discuss whether it is likely that these problems are present in our model.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the elastic modulus of the material used to construct

Given a type of material used in a wire with diameter (d = 0.25 in) that stretches 2.3 inches while 80 feet of length is under tensile load of 1800 pounds. Find the elastic modulus of the material used to construct the wire.

  Story building in order for major masonry rehabilitation

Scaffolding is to be constructed on all faces of a six-story building in order for major masonry rehabilitation work to be performed. The exposed surface area of the exterior walls of the building has been estimated to be 423,000 sq. ft. Historical r..

  Determine the reactions at the supports

he tapered member is fixed connected at its ends A and B and is subjected to a load P = 7 kip at x =30in. Determine the reactions at the supports. The material is 2in. thick and is made from 2014-T6 aluminum (Eal = 10,600ksi).

  Determine what is the probability of failure of the antenna

A large parabolic antenna is designed against wind load. During a wind storm, the maximum wind-induced pressure on the antenna, P, is computed as P= 1/2CRV^2 Where C = drag coefficient, R = air mass density in slugs/ft3,

  How many degrees of freedom are present

Determine the relationship which governs the velocities of the two cylinders A and B. Express all velocities as positive down. How many degrees of freedom are present?

  Express f in cartesian vector form using coordinate system

The cable from point A to point B exerts a 900 N force on the top of the television transmission tower that is represented by the vector F. Express F in Cartesian vector form using the coordinate system.

  Determine the mass fractions of the constituents of air

The composition of moist air is given on a molar basis to be 78 percent N2, 20 percent O2, and 2 percent water vapor.

  Determine the maximum power output of the pelton wheel

The Pelton wheel is 3.0 m in diameter, and the nozzle exit is 0.2 m in diameter. Determine the maximum power output of the Pelton wheel. Is a Pelton wheel the appropriate turbine type for this application

  Notch fracture toughness show your supportin calculations

A Charpy V Notch test was conducted for an ASTM A572 Grade 50 bridge steel. the average values of the test results at four different test temperatires were found to be

  Determine the cratess velocity when the crate reaches point

If the force is removed when the crate reaches point B, and the crate is then released from rest, determine the crates's velocity when it slides back down the plane and reaches point A.

  What do will result if the concentration of the waste

The discharge from the Renenutet sugar beet plant causes the DO at the critical point to fall to 4.0 mg/L. The Meskhenet Stream has a negligible BOD and the initial deficit after the river and wastewater have mixed is zero

  Determine the dry density of the soil

A small hole about 4" in diameter and 6" deep is dug into acompacted layer of a soil embankment. 2.96 lbs of motor oil withGs=0.92 is required to fill the hole.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd