Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
For the pendulum shown in the figure,the restoring torque due to gravity is given by T=mgLsin(thita). Derive the linearised equation about the operation point thita=0.
Explain and justify ideas that could have made the development of the design more effective. Support your recommendations with specific examples as appropriate.
A lap joint needs to be designed using 20-mm diameter bolts to carry a load of 120 kN on the connecting plates. If the shear stress in each rivet is not to exceed 90 MPa, determine the number of bolts needed.
a fully loaded lorry has a mass of 10 tonnes and is travelling along a road at uniform velocity when the brakes are applied and the lorry is brought to rest. if the deceleration is 2m/s2 and the coefficient of rolling friction is 0.15, determine t..
The state charged the Todesca corporation with motor vehicle homicide, and the jury found the company guilty. The trial judge imposed a fine-of $2,500. The court of appeals reversed the conviction, and the prosecution appealed to the state's highe..
What is the initial velocity of Block B, constant acceleration of Block A, velocities of both blocks at t=3s, and the total distance traveled by block B from t=0s to t=3s?
Identify the difference between intensive, exclusive, and selective levels of distribution intensity? Give an example of a product that would be best for each level of distribution.
showing the two upward pulls of the rings on his hands, each of size 380N. Calculate the angle between the wires supporting the rings and the vertical.
an automobile having a mass of 2000 kg deflects its suspension springs 0.02 m under static conditions. Determine the natural frecuency of the automobile in the vertical direction by assuming dumping to be negligible.
the 2-kg collar is released from rest at A and travels along the smooth vertical guide. determine the speed of the collar when it reaches position B.Also ,find the normal force exerted on the collar at this position.the spring has an unstrectched ..
Respond to the question Is it morally sufficient for a U.S. company to comply with the laws of the foreign country in which it operates? Why or why not? What guidelines should a multinational use to determine a fair wage to its employees in a less..
Determine the thermal efficiency of the cycle and the net specific work. Assume each turbine stage isentropic efficiency to be 99% and assume the FWH is open.
The total force Fa + Fb exerted on the shelter is in the direction parallel to the line L and it's magnitude is 400 lb. Graphically determine the magnitudes of Fa and Fb.
determine the smallest allowable value of the coefficient of static friction between the collar and the rod if the collar is not to slide when a) a =15° b)a = 45°. Indicate for each case the direction of the impending motion.
Calculate the static thrust of the turbojet engine having mass flow 88lbm/sec the ratio of air and fuel mass flowing into the turbojet is 50:1 and it's exhaust plane the velocity is 1640 ft/sec and pressure is same as ambient pressure?
One kilogram of air as an ideal gas executes a Carnot power cycle having a thermal efficiency 50%. The heat transfer to the air during isothermal expansion is 50 kJ. At the end of the isothermal expansion, the pressure is 574 kPa and the volume is..
Single degree of freedom vibration problems with forcing functions, Need help with this Undergraduate problem where two dampers are in series.
A heat pump with a COP (coefficient of performance) of 2.8 is used to heat an air-tight house. When running, the heat pump consumes 5 kW of power
The nominal breaking strength of the rope is 10,000 lbs. Calculate how much payload this assembly can allowably pick up. Show your work.
A long electric wire of radius r0 generates heat at rate of q'''. The surface is maintained at uniform temp of T0. Write heat equation and boundary conditions for steady state one dimensional conduction.
If after 49.5 h the concentration of carbon is 0.35 wt% at a position 4.0 mm below the surface, determine the temperature at which the treatment was carried out.
A similar measurement is made applying the force parallel to one of the cube axes. Explain why the two measurements give different values of the elastic modulus.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: info@expertsmind.com
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd