Define what are the molar enthalpy and total enthalpy

Assignment Help Chemistry
Reference no: EM13145907

Five grams of the specified pure solvent is placed in a variable volume piston. What are the molar enthalpy and total enthalpy of the pure system when 50% and 75% have been evaporated at: (i) 30°C, (ii) 50°C? Use liquid at 25°C as a reference state. a.Benzene (?L = 0.88 g/cm3) b.Ethanol (?L = 0.79 g/cm3) c.Water without using the steam tables (?L = 1 g/cm3) d.Water using the steam tables

Reference no: EM13145907

Questions Cloud

Compute the probability of a successful operation : Compute the probability of a successful operation (i.e., an operation in which at least one hit is a success) if all 3 missiles are launched and a hit within 40 miles of the target is considered a success.
Calculate the density of hydrogen bromide gas : Calculate the density of hydrogen bromide gas (in g/L) at 733 mm Hg and 47 degrees Celsius
Determine if reason for component failures is independent : Use an appropriate test to determine if the reason for component failures is independent of their designs. Show your manual calculations here.
Calculate the moles of argon present : A 355 m-L container holds .146 g of Ne and an unknown amount of Ar at 35 degrees C and a total pressure of 626 mmHg. Calculate the moles of Ar present.
Define what are the molar enthalpy and total enthalpy : What are the molar enthalpy and total enthalpy of the pure system when 50% and 75% have been evaporated at: (i) 30°C, (ii) 50°C? Use liquid at 25°C as a reference state
Explain why an observed value of hours is not unusual : Explain why an observed value of 250 hours is not unusual for an individual light bulb, even though it is outside the confidence interval you calculated.
Products using the relative sales value to split off : Allocate joint costs to the two products using the relative sales value to split off as the allocation basis.
Explain the transfer of energy and bioaccumulation : Explain the transfer of energy and bioaccumulation through primary , secondary, tertiary, and quaternary trophic levels. You may answer this part of the question by drawing a diagram and using arrows where applicable .
Compute the pressure of the hydrogen gas : Assume you carry out an experiment when the atmospheric pressure is 765mmHg and the temp in 24 degrees C. you collect Hydrogen gas and want to know the pressure of the gas

Reviews

Write a Review

Chemistry Questions & Answers

  What is the partial molar volume of the ethanol

At 25 degree celcius, the density of a 50 percent by mass ethanol/water solution is 0.914 g per subic centimetre. Given that the partial molar volume of water in the solution is 17.4 cubic centimeter per mol.

  How many joules of heat are absorbed

The temperature of a 35.2 g sample of iron increases from 23.7 °C to 29.5 °C. If the specific heat of iron is 0.450 J/g-K, how many joules of heat are absorbed?

  How much energy would it take to raise the temperature

The molar heat capacity of silver is 25.35 J/mol * C. How much energy would it take to raise the temperature of 8.60 g of silver by 11.1 C?

  Arrange the four compounds in order of increasing volatility

Arrange the four compounds below in order of increasing volatility.

  What is the density of the metal

A calibrated flask was filled to the 25 mL mark with ethyl alcohol. By weighing the flask before and after adding the ethyl alcohol, it was determined that the flask contained 19.7325 g of alcohol.

  Define titration of a weak acid with a strong base

Titration of a Weak Acid with a Strong Base, Find the pH before, at, and after equivalence point of 35 ml of 0.15 M lactic acid with 0.18 M NaOH.

  Calculate the enthalpy of formation of acetylene

The enthalpy of combustion of acetylene C2H2 is C2H2(g) + 5/2O2(g) ->2CO2(g) + H2O(l) H°rxn= -1299 kJ Calculate the enthalpy of formation of acetylene, given the following enthalpies of formation H°f[CO2(g)] = -393.5 kJ/mol ,H°f[H2O(l)] = -285.8 k..

  Calculate amount of 10.00% acetic acid you will need to add

Calculate the amount of 10.00% acetic acid you will need to add to 100.0 mL of your milk in order to bring the final acidity to 1.00% acetic acid.

  Which of intermolecular force is present in nitromethane

Nitromethane has a relatively high boiling point of around 100 c. Which of the following intermolecular force is not present in pure liquid nitromethane and why.

  What is the final concentration

63mL of a 1.70 M solution is diluted to a volume of 218 mL. A 109mL portion of the solution is diluted using 117mL of water. What is the final concentration?

  Determine the partial pressure of the product phosgene

The Kp for the reaction below is 1.49 × 108 at 100.0 °C: CO (g) + Cl2 (g) ↔ COCl2 (g)

  .how many moles of cl are present

Zinc chloride (ZnCl2) is 52.02% chlorine by mass. What mass of chlorine is contained in 65.0 g of ZnCl2?Answer in units of g.How many moles of Cl is this?Answer in units of mol.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd