Compute the excess elastic energy e associated with this

Assignment Help Civil Engineering
Reference no: EM13531096

A significant obstacle in the design of atomic weapons is theso-called delta phase instability (a type of mixed dislocation) inPu-239. This is the problem: We wish to construct a sphericalatomic bomb core out of pure delta phase (f.c.c.) Pu-239. A deltaphase instability has shear strain θ = er and shearstress T = (sinr)/2πr2 where r is in cm, θ isunit less, and T is in units of N/cm2 . Assume that forthe purposes of elastic energy calculations ro = 0, andthat there is a single instability. The density of Pu-239 is listedas 19.8 gm/cc. Compute the excess elastic energy E associated withthis instability. Be very careful with units and dimensions.

Reference no: EM13531096

Questions Cloud

What rate is water being stored in the river : Water flows in a river. At 8 a.m. the flow past bridge 1 is 2150cfs. At the same instant the flow past bridge 2 is 1800 cfs. At what rate is water being stored in the river between the two bridges at this instant? Assume zero seepage and negligible e..
Speeds could a vehicle be operated without sliding inward : If the actual coefficient of sliding friction on icy pavementis 0.05, theoretically within what range of speeds could a vehiclebe operated without sliding inward or outward for the following problems.
What is the reynolds number for water flowing : In older houses one will often find steel waterpipings whereascopper tubing is now generally used. While carrying out renovationsplumbers often interconnect the steel pipings with Copper tubings.Is this a sound practice? Explain.
What is the minimum coefficient of road adhesion needed to : A Parshall flume with a throat width of 2.50 feet is used to measure discharge.  If the measured depth, H, is 1.8 feet, what is the discharge? Need to know how to solve for the discharge.
Compute the excess elastic energy e associated with this : A significant obstacle in the design of atomic weapons is theso-called delta phase instability (a type of mixed dislocation) inPu-239. This is the problem: We wish to construct a sphericalatomic bomb core out of pure delta phase (f.c.c.) Pu-239. A de..
And that stead state conditions have been attained : The Purification of hydrogen gas by diffusion through apalladium sheet was discussed. compute the number of kilograms ofhydrogen that pass per hour through a 6-mm- thick sheet of palladium having an area of 0.25 m^2 at 600
Determine the allowable compressive force : The allowable stresses are as follows:compressive stress in the spar, 70 MPa; shear stress in the pin, 45MPa; and bearing stress between the pin and the connecting plates,110 MPa.
A soil sample has the following data : A soil sample has a wet unit weight of 96 lb/ft^3, amoisture content of 17% and a degree of saturation of 60%. Findthe: (A) Void Ratio, (B) Specific gravity, (C) Saturated unitweight.
Calculate the average stress in the plane of the reduced : A 1.0-in-diameter hole is drilled on the centerline of a long, flat steel bar that is 1/2" thick and 4" wide. The bar is subjected to a tensile load of 30,000 lb. Calculate the average stress in the plane of the reduced cross section and the maxium t..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate and print out the squares of all the even integers

write the matlab statements required to calculate and print out the squares of al the even integers between 0 and 50. create a table consisting of each integer and its square, with appropriate labels over each colum.

  Estimate the minimum do and the critical location in river

If the ultimate BOD of the mixed river water is 30mg/L, the rate constant for BOD at 20ºC is 0.6d-1, the reaeration rate constant at 20ºC is 0.8d-1, and the removal of BOD by sedimentation can be neglected

  Describe with the aid of diagrams explaining why and when

Describe with the aid of diagrams explaining why and when boundary layer separation occurs. c)Describe some methods to prevent boundary layer separation

  Determine the change in each lateral dimension

At the proportional limit, a 32-mm-thick by 87-mm-wide bar elongates 10.2 mm under an axial load of 532 kN. The bar is 2.4 m long. Poisson%u2019s ratio, , for the material is 0.27.

  Minimizing the tension tab

What should TAC , TAB and the acute angle ? between TAB and the vertical to minimize the tension TAB ? Take o and W = 1,000 N. Hint: Consider various possible force triangles and decide on inspection how to minimize TAB.

  Find the require concrete dimension and prestressed force

Flange thickness hf= 0.2h and web width bw=0.4. The member will be prestress using graded 270 strand. Time dependant losses are estimate at 20% of Pi. Normal density concrete will be used with f'c = 5000 psi

  What is concentration of fe needed to maintain concentration

At a wastewater treatment plant, FeCl3 (s) is added to remove excess phosphate from the effluent. Assume the following reactions occur: FeCl3(s) Fe3+ + 3Cl- Fe3+ + PO4 (3-) FePO4 The equilibrium constant for the second reaction is 10^26.4.

  Determine what is the change in the wires total resistance

You have two wires connected end to end. Wire 1 is copper and wire 2 is made using a special carbon conductor. Wire 1 has a resistance of 0.215 ohms/ft and is 500 ft long. Wire 2 has a resistance of 0.141 ohms/ft and is 700 ft long.

  Calculate what is the volume of rock in the rock pile

A storage pile of crushed rock is 100ft by 100ft square at its base and 50 ft by 50 ft square on the top. The pile is 25 ft high. What is the volume of rock in the rock pile

  Calculate the head loss with a roughness height

A galvanized iron pipe with a roughness height (e) of 5x10-6 m with a diameter (D) of 0.05 m and a length (L) of 100 m carries a discharge (Q) of 0.003 m3/s. Calculate the head loss (hL).

  Calculating the ph of solution

A 1.50 L buffer solution is 0.250 M in HF and 0.250 M in NaF. Calculate the pH of the solution after the addition of 0.0500 moles of solid NaOH. Assume no volume change upon the addition of base. The Ka for HF is 3.5 x 10 -4 .

  Standard deviation in lines of levels

Lines of levels were run requiring n instrument setups. If the rod reading for each backsight and foresight has a standard deviation δ what is the standard deviation in each of the following level lines?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd