Calculate the time required to filter and wash the cake

Assignment Help Chemical Engineering
Reference no: EM131061429

A slurry is filtered, and the filter cake is washed by use of a plate-and-frame filter press operated at a constant pressure drop of 40 psi throughout the entire run. Experimental tests have been carried out on this equipment, and the results for the slurry mixture used can be expressed as follows for any one pressure drop:

1551_1e851325-e81c-4a18-80ca-2d5c7a17f304.png

where k' and k" are constants. At a pressure drop of 40 psi, 0.02 lb of filtrate is collected in 1.8 min for each square inch of cloth area, and 0.08 lb of filtrate per square inch of cloth area is collected in 22.2 min. Calculate the time required to filter and wash the cake formed when 0.11 lb of filtrate has been collected per square inch of cloth area if an amount of wash water equal to half the filtrate is used. The specific gravities of the filtrate and wash water are 1.0, and both are at the same temperature. Simple forward washing is used so that the washing rate is equal to the filtrate delivery rate at the end of the filtration.

Reference no: EM131061429

Questions Cloud

Bromamide degradation reaction : 2. Which of the following atoms has the highest first ionization energy? (1) Na (2) K (3) Sc (4) Rb 3. In the Hofmann bromamide degradation reaction, the number of moles of NaOH and 2 Br used per mole of amine produced are:
Estimate the pounds of steam required per hour : The leaving vapors will contain water vapor at a pressure equivalent to the equilibrium vapor pressure of water at 15°C. If a suction pressure of 2.0 in Hg absolute is to be maintained by the jet, estimate the pounds of steam required per hour to ..
Unsuitable for drinking due to high concentration : The concentration of fluoride, lead, nitrate and iron in a water sample from an underground lake was found to be 1000 ppb, 40 ppb, 100 ppm and 0.2 ppm, respectively. This water is unsuitable for drinking due to high concentration of : (1) Lead (..
Provide an example of a work-related change : Discuss three of the tactics that can help reduce resistance to change - particularly those that may prove most effective in your example.
Calculate the time required to filter and wash the cake : Experimental tests have been carried out on this equipment, and the results for the slurry mixture used can be expressed as follows for any one pressure drop:
What is the companys return on investment : Milton Inc. generates annual revenue of $375,000,000 and incurs annual costs of $95,000,000. The initial investment amounts to $450,000,000. What is the company's return on investment?
Discuss the public service culture present in the case : Identify and discuss the public service culture present in the case and explain why Wise argue that public service motivation is found more in the government than in private sector
Describe strategic philanthropy in your own words : Benefits of Strategic Philanthropy- Describe strategic philanthropy in your own words. Does strategic philanthropy influence your brand loyalty? Why or why not
Problem regarding the buffer solution : You have 100 mL of a 0.15 M solution of NaH2PO4. How many grams of Na2HPO4 must you add if you want to make a buffer solution for which the pH equals the pKa of H2PO4-?

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Compute control limits for average and range control chart

Use the information in the above table to compute the Control Limits for an Average and a Range Control Chart.

  Indicate type of sensors

A factory is producing tablets. It is required to design a system such that: The bottles moves till it reach the position shown (A) and 50 tablets are dropped in

  Process industry in oman and prepare a report

Test the knowledge and understanding of the concepts and procedures for process instrumentation and communication systems used in process industries.

  Calculate atomic packing

The unit cell for Cr2O3 has hexagonal symmetry with lattice parameters a = 0.4961 nm and c = 1.360 nm. If the density of this material is 5.22 g/cm3, calculate its atomic packing factor.

  Calculate the selectivity of ethylene for ethanol

A typical feed stream composition is 55% ethylene, 5% inserts, and 40% water. A typical product stream is 52.26% ethylene, 5.49% ethanol, 0.16% ether, 36.81% water, and 5.28% inserts. Calculate the selectivity of ethylene for ethanol and for ether..

  Compute graphically the flowrate and the pump head

Compute graphically the flowrate and the pump head at the operation conditions - Repeat the question for the case of two identical pumps in series

  Logistics vendor for handfield manufacturing

Monczka-Trent Shipping is the logistics vendor for Handfield Manufacturing Co, in Ohio. Handfield has daily shipments of a power-steering pump from its Ohio plant to an auto assembly line in Alabama. The value of the standard shipment is $250,000...

  Equilibrium data for this system

Acetone is to be extracted from a solution in water, using 1,1,2-trichloroethane. The feed concentration is 45.0% w/w acetone. Determine the number of stages required to reduce the concentration of acetone to below 10%, using 32 kg of extraction-s..

  Adsorption system to recover solvent

An electronics plant uses an adsorption system to recover solvent from a vent gas stream and prevent volatile organic compound (VOC) emissions. The vent gas flow rate is 20 m3 /s of dry air at 293 K, 1.5 atm.

  Determining the average atomic weight

with an atomic weight of 51.9405 amu, 9.50% of 53Cr, with an atomic weight of 52.9407 amu, and 2.37% of 54Cr, with an atomic weight of 53.9389 amu. On the basis of these data, confirm that the average atomic weight of Cr is 51.9963 amu.

  A particle with the mass of a proton is trapped in a box

A particle with the mass of a proton is trapped in a box. The particle falls from the state to the state and emits 0.16 meV of energy. What is the size of the box?  (nm

  Calculate the flowrate of the oil

1a / state the formula giving flowrate (qv) in terms of valve flow coefficient, pressure drop across the valve and relative density of fluid. State the units of the variables in the formula.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd