Calculate the hp per foot of cutting edge ratio for all four

Assignment Help Civil Engineering
Reference no: EM13562675

The Caterpillar D6R Series 3 and D8R tractors are rated, respectively, at flywheel horsepowers (fwhp) 0f 185 and 305. The “A,” “S,” and “SU” blade widths (length) for the D6R are S, 16 ft, 9 in.; A, 17 ft, 1 in.; and for the

D8R SU-21 ft, A, 21 ft, 7 in.  Calculate the hp per foot of cutting edge ratio for all four conditions.

Reference no: EM13562675

Questions Cloud

Design a curve for the highway by computing the radius : A horizontal curve is being designed for a new two-lane highway(12-ft lanes). The PI is at station 250 + 50, the design speed is 65 mi/h, and a maximum superelevation of 0.07 ft/ft is to be used
Determine the crest and sag vertical curves required : Two level sections of an east highway (G=0) are to be connected. Currently, the two sections of highway are seperated by a 4000-ft (horizontal distance), 2% grade. The westernmost section of highway is the higher of the two and is at elevation 100 ft..
What is the elevation of the pvt : An equal-tangent crest vertical curve is designed for 70 mi/hr. The high point is at elevation 1011.4 ft. The initial grade is +2% and the final grade is -1%. What is the elevation of the PVT? Solve this problem with the parabolic equation rather tha..
What microbial mediated process do you suspect is occurring : You find a chlorine demand occurring in your drinking water distribution system (series of pipes that carry drinking water throughout a city), yet there is no increased chlorine demand in the water going through the treatment plant
Calculate the hp per foot of cutting edge ratio for all four : The Caterpillar D6R Series 3 and D8R tractors are rated, respectively, at flywheel horsepowers (fwhp) 0f 185 and 305. The “A,” “S,” and “SU” blade widths (length) for the D6R are S, 16 ft, 9 in.; A, 17 ft, 1 in.; and for the
What is the equivalent height of a water column : Tall buildings can develop a significant difference in pressure between the inside and the outside of the building. Air lock entrances are used at the ground level so the pressure at the ground floor is not the same as atmospheric pressure. Assume th..
Determine how much he will weigh on the spring scale : An undisturbed chunk of soil has a wet weight of 62 lb and a volume of 0.56 ft3. When dried out in an oven, the soil weighs 50 lb. If the specific gravity of soilds is found to be 2.64
Find the dry unit weight void ratio and degree : The area of a parking lot is calculated to be 5,474 ft^2 with an estimated standard deviation of 2 ft^2. What is the maximum anticipated error? there is a 90% chance that the error range will be what?
How fast was the car traveling before applying the brakes : You have been hired to review an accident scene where a vehicle hit a light pole at the intersection of main and 5th. The vehicle was estimated to hit the light pole at 30 mph.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the maximum negative moment in each span

determine the maximum negative moment in each span and maximum negative moment at each support. remember that live loads shall be placed so as to cause the greatest effect. specify the method that you used to determine the moments.

  Length of contracted rectangular weir

A trapezoidal canal 6m wide at the bottom and having a side slope of 1V:2H carries water with a mean velocity of 1.0m/s to a depth of 60cm. What length of contracted rectangular weir 1.0m high should be placed at the middle of the canal to make th..

  What torque is required to rotate the inner cylinder

Crude oil at 20 degrees C fills the space between 2 concentric cylinders 250mm high with diameter of 150 and 156mm. What torque is required to rotate the inner cylinder at 12 rev/min

  The mechanical properties of aluminum may be improved

The mechanical properties of aluminum may be improved by incoporating fine particles of lauminum oxide (al2O3) Given that the moduli of electricity of this material are respectively 69GPa and 393 GPa plot modulus

  Does the second law require that the decrease in entropy

An insulated system contains two solid blocks in contact with each other; one hot and the other cold. After heat transfer over some time,thermal equilibrium is established in the container.

  Indicate a maximum rate of climb and rate of descent

1.Remain at the previously indicated rate of climb 2.Fall to zero rate of climb indication 3.Indicate a maximum rate of climb 4.Indicate a maximum rate of descent

  Figure if the authorities intend to spend exactly

Foxton village is 10 miles north of an abandoned road that goes from east to west grimley leaving. POINT OF abandoned road closest to Foston is 40 miles from grimley County authorities are to build a new road linking

  The lower surface is stationary and contains

Two infinite parallel horizontal surfaces are seprated by a film ofSAE 10W oil at T=10 C that is d=0.0144 in. thick . The uppersurface moves with speed V

  Determine if the driveway will be affected

A developer wants to provide access to a new building from a driveway placed 1000 ft upstream of a busy intersection.  He is concerned that queues developing during the red phase of the signal at the intersection will block access.  If the speed on t..

  What is the concentration of bod in the jackson river

The James Rives flows in from the East at 320 m^3/min and joins the Jackson River flowing at 605 m^3/min just outside the town of Charlotte, NC. The concentration of BOD in the James River is 14 mg/L.

  Where to locate the mass center of the assembly

The two upper lengths of the welded Y-shaped assembly of uniform slender rods have a mass per unit length of 0.3 kg/m, while the lower length has a mass of 0.7 kg/m. Locate the mass center of the assembly. lenghts of all rods aew 30mm

  Design horizontal curve with degree central angle for lanes

Design a horizontal curve with a 40-degree central angle (delta=40) for a two-lane road with 11-ft lanes. The design speed is 70 mi/h and superelevation is limited to 0.06ft/ft. Give radius, degree of curvature, and length of curve

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd