Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A rigid rectangular shelf is suspended from a rigid ceiling by mean of four rods of diameter .505 inches. The two rods to the left L1 and L2, are made of steel. The two rods to the right R1 and R2 are made of aluminum. Two weights are positioned on the platform - the larger weight of 10 kips at the left and the smaller weight of 5 kips to the right. The Est = 30E3 ksi, Eal=16E3 ksi, Vst=.3, and Val=.33
a. calculate the stress in L1 and L2
b. calculate the stress in R1 and R2
c. calculate the axial strain and the transverse strain in the steel rods.
d. Calculate the axial strain and the transverse strain in the aluminum rods.
e. If the original length of all four rods is 10ft, calculate the total axial deformation in the steel rods.
f. If the original length of all four rods is 10ft calculate the total axial deformation in the aluminum rods.
Assume that during the analyze stage an obvious solution is discovered. Should that solution be immediately implemented and the remaining steps of DMAIC abandoned?
A tangent section of highway has a -1.0 % grade and ends at station 0+145 and elevation 25m. it must be connected to another section of highway that has a -1.0 % grade and that begins at station 1+345 and elevation
A trapezoidal channel has a bed width of 3.5 m and a side slope of 30 degrees from the horizontal. Determine the critical depth and the critical velocity for a flow of 22 cubic meters per second.
The hypothetical velocity distribution in a horizontal, rectangular open channel is V=0.3y (m/s), where V is the velocity at a distance y (m) from the bottom of the channel. If the vertical depth of flow is 2 m and the width of the channel is 4 m,..
What are the specifications need to be specified while creating a design for waterways?what are their uses?how are they maintained?
NH4+ = N+ + NH3 pK =9.24 If the pH is 8.5 and the ammonium(NH4+) concentration in 20mg/L, calculate the ammonia(NH3) concentration in mg/L.
a spot speed study was conducted on a freeway on which the mean speed and the standard deviation were found to be 72 .4 mi/hr and 5.4 mi/hr, respectively. what is the range of the values that would be expected to contain the middle 95 percent of s..
the tank contains water to depth of 2m and oil (sg=.8) on top of the water to a depth of 1m detrermine the magnitude and location of the resultant fluild force acting on one end of the tank
If the overall gear reduction ratio is 8 to 1, what is the maximum acceleration from rest (in ft/sec^2) for: a) the car with the base engine? b) car with the modified engine? Assume the car is on good dry pavement.
An emf of 22.0 mV is induced in a495 turn coil when the current is changingat a rate of 5.0 A/s. What is the magneticflux through each turn of the coil at an instant when the currentis 1.00 A
Reservoir A (water surface elevation = 1300 ft) is connected to reservoir B (water surface elevation=250 ft) by 6,000 ft of 14 inch diameter cast iron pipe (e = 0.005 ft. Neglecting all minor losses
A driver takes 3.2 sec to react to a complex situation while travelling at a speed of 96km/hr.how far does the vehicle travel before the driver initiates a phisical response to the situation?
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd