A ball is thrown with a velocity of 25ms at a building the

Assignment Help Civil Engineering
Reference no: EM13383446

A ball is thrown with a velocity of 25m/s at a building. The building is 20m high; the man throwing the ball is 40m from the front wall and is standing in depression so that the ball leaves at his hand at the same elevation as the base of the building. If the ball strikes the side of the building 2s after being thrown, at what height above the base of the building did the ball strike the building? What is the velocity of striking? 

Reference no: EM13383446

Questions Cloud

A cylindrical soil sample 73 cm in diameter and 168 cm long : a cylindrical soil sample 7.3 cm in diameter and 16.8 cm long is tested in a constant head permeability apparatus. a
Assume that the primary hdlc station in normal response : assume that the primary hdlc station in normal response mode has sent six i-frames to a sencondary station. the
A cylindrical specimen of a brass alloy 100 mm 039 in in : a cylindrical specimen of a brass alloy 10.0 mm 0.39 in. in diameter and 120.0 mm 4.72 in. long is pulled in tension
If a rod of brass 035 m long is heated from 150 to 850c : if a rod of brass 0.35 m long is heated from 150 to 850c while its ends are maintained rigid determine the type and
A ball is thrown with a velocity of 25ms at a building the : a ball is thrown with a velocity of 25ms at a building. the building is 20m high the man throwing the ball is 40m from
Azero-order reaction has a constant rate of 340times10-4 : a zero-order reaction has a constant rate of 3.40times10-4 . if after 45.0 seconds the concentration has dropped to
The container is 283cm higher than the level in the arm : what is the pressure in atm inside a container of gas connected to a mercury filled open-end manometer when the level
A beam of light strikes a sheet of glass at an angle of : a beam of light strikes a sheet of glass at an angle of 57.0circ with the normal in air. you observe that red light
Determine the kelvin temperature required for a 00470 mol : determine the kelvin temperature required for a 0.0470 mol of gas to fill a balloon to 1.20 l under 0.988 atm of

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the amount of changes in length of the rod

If the resistivity of this alloy is dependent only on thermal and impurity considerations, find the amount of changes in length of the rod (in mm) when the temperature is changed from T1 to 1.47268x10^2 °C.

  Calculate the largest tolerable internal crack length

Calculate the largest tolerable internal crack length for a 7075-T651 aluminum alloy component that is loaded to a stress one-half of its yield strength without catastrophic fracture. For the alloy, the plane strain fracture toughness is 24 and yi..

  Draw thermal circuit of heat flow from center of pipe to t

Steam at 100 psia, sat vapor is in a pipe. The pipe is schedule 40 steel with a wall thickness of 1/8 inch and a length of 100 ft. The outside air temperature is 40 degrees Fahrenheit. The mass flow of steam is 4,000 lb/hr.

  What force must be applied at each connection

A concentrated downward force of 2000 lb. is located 6' from the left support, and a uniformly distributed load of 200 lbs./lin. ft. begins 6' to the right end of the member. What force must be applied at each connection to maintain equilibrium?

  Determine the force exerted on the tank bottom

A cylindrical water tank is suspended vertically by its sides. The tank has a 10-ft diameter and is filled with 20 degree celcius water to a 3-ft depth. Determine the force exerted on the tank bottom

  Estimate the diffusion distance of a carbon atom in fe

The variation in the diffusion coefficient with temperature, over an appropriate range of temperature, can usually be approximated as follows: D= (D0)e^-(Q/(KT) where, Q = activation energy (eV/atom) and k = Boltzmann's constant (8.616*10-5 eV/ato..

  What input of power rating is required for pump to refill

A water storage tank located on a larege dairy farm has a storage capacity of 0.1 ML. The average rate of water consumption from this tank is 6.25 kL per day, every day. The farmer refills the tank (overnight) every 14 days

  Design a rectangular section for cantilever beam that spans

Roe is the ratio of nonprestressed reinforcement in a section, and roe balanced is the ratio of tensile reinforcing producing balanced strain condition. Show cross sections, including bar sizes, arrangements, and spacing.

  Determine the distance the ball is from the origin 4s

A 7 lb particle at rest is subjected to the action of its weight and forces F1= (2i+6j-2tk)lb, F2=(t^2i -4tj-1k) lb, and F3 =(-2ti) lb, where t is in seconds. the particle starts at the origin (0,0,0)

  What is force of water on spillway whose upstream is given

What is the force of the water on a spillway whose upstream depth is 1.2m and whose downstream depth is 0.2m. The width of the spillway is 3m.

  Determine amount of coal used per day if heat of combustion

A coal fired power plant can be modeled as a heat engine. If the power output of the plant is 200 MW and the thermal efficiency is 42%, determine the amount of coal used per day if the heat of combustion from the coal is 24,000 kJ/kg.

  Determine what is the mass of the particles collected

a stream f gas flowing at 3000 cfm has a particulate loading of 50gr/ft what is the allowable exit loading if 95 % collection efficiency is required. what is the mass of the particles collected

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd