Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A stack( T=550 deg F and 750mm Hg) was sampled using EPA Method 5. The total gas volume that flowed through the dry gas meter was 2.785 cubic meters (at T = 60 deg F and P = 800 mm Hg). The mass of PM (particulate matter) was 1.50 g. Also, 72.0 g of H20 was collected in impingers.
a. Calculate the concentration of PM in the stack (micrograms/cubic meter) at stack conditions.
b. The stack gas exits at an average velocity of 20 m/s, and the stack has an inside diameter of 5m. What is the emission rate of PM, in kg/day.
c. What is the PM concentration in micrometers/dcsm?
A steel bar is attached to a wood support beam with four 20 mm diameter lag screws. The steel bar is 75-mm-wide by 6-mm-thick. For the steel bar, the yield strength is 260 MPa and the ultimate bearing strength is 350 MPa.
Determine the magnitude of reaction at point A (in kips) of a 20' beam with 5kips at 4' of the beam and 2kips at 9' of the beam at 350lbs./ft.
A u-tube manometer is used to measure the pressure of a vessel under vacuum. Assume the manometer is open to atmospheric pressure (101.325 kPa) and the density of the fluid in the manometer is 12 g/cm3.
On a certain highway a -6% grade meets a +2% grade at station 70 + 00, elevation 550.97 ft. An equal tangent vertical curve, 800 ft. long, is to be installed to connect these two grades.
A HEPA (high efficiency particulate air) filter is monitored periodically for replacement. Specifications state that if the pressure drop across the filter exceeds 1 inch of water, the filter should be replaced.
An element of aluminium in a form of a rectangular parallel pipe has a length 'a' along the x axis of 5.5 in, a length 'b' on the y axis of 4.5 in. Determine the maximum shear stress in the material,the change in length.
If a torque of T = 1,100 N-m is applied to the composite assembly, determine: (a) the maximum shear stress in the aluminum tube and in the steel core. (b) the rotation angle of end B relative to end A.
A horizontal curve is designed for a two-lane road in a mountainous terrain. The following data are known: Deflection angle: 40 degrees Tangent: 436.76 Station of PC: 2695 + 73.89 Side friction factor = 0.12 Superelevation = 8% Superelevation run-off..
an engineer uses a standard technique for measuring the thickness of a clay landfill liner that has a typical standard deviation of 0.7 in. The project specifications require the liner thickness to be 36 inches or more, at least 95 percent of the ..
A fireworks shell is launched vertically from point A with speed sufficient to reach a maximum altitude of 500ft. A steady horizontal wind causes a constant horizontal acceleration of 0.5ft/sec^2, but does not affect the vertical motion.
The compound interest formula is F=P(1+i)n where F is the total amount due, P is the initial cost or amount of money, i is the interest rate, and n is the number of periods interest is computed. 1.A student purchases a $1400 laptop computer for sc..
a tension member with cross-sectional area 3 in2 resists a load of 10 kips. How do you Calculate the normal and shear stress on planes making a 0, 20, 45, and 60 angle with the transverse section.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd