Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A u-tube manometer is used to measure the pressure of a vessel under vacuum. Assume the manometer is open to atmospheric pressure (101.325 kPa) and the density of the fluid in the manometer is 12 g/cm3. When the vessel is under 9 psi of vacuum, the height of the fluid column is 83 cm. If the vessel partially loses vacuum and is now under 1.0 psi of vacuum, what will be the new height of fluid column. THE HEIGHT IS FROM THE BOTTOM OF THE U-TUBE TO THE TOP OF THE FLUID ON THE Patm SIDE.
assuming that the velocity variation within the main channel and the floodplain subsections is much smaller than the change in mean velocities between subsections, find the value of the kinetic energy correction coefficient.
Determine the effective size as well as the uniformity coefficient and coefficient of curvature for each soil. Determine also the percentages of gravel, sand, silt, and clay according to (a) ASTM, (b) AASHTO, (c)USCS, and (d) the British Standard.
a). Determine the state of stresses in the walls and indicate these stresses (including arrows to denote the direction of the stresses) on the element below. b). Then, determine the maximum in-plane shear stress on the wall of the pipe using Mohr's..
Dispute in largest open-pit copper mine, My recollection may be skewed, so for our purposes, consider this example a hypothetical, but this is my recollection of a real case. In the early 80s, in Salt Lake County, Utah, a dispute arose involving t..
velocities in a 200-mm-diameter circular conduit, measured at radii of 0,36,64, and 87 mm were 7.0, 6.8, 6.1, and 5.0 m/s, respectively. Find the approximate values (graphically) of the volume flow rate and the mean velocity.
A 1 cm diameter, 0.4 m long steel rod is to be used in an application where it will be subjected to an axial tensile force of 15kN. The factor of safety based on yield stress must be at least 1.5, and the axial deformation must not exceed 2 cm.
What is the corresponding horizontal distance between the points - The slop distance 156.777 from one poin to another at rate of+1.5%
This material is related Geotechnical Engineering, please only answer if you are certain and sure of your answer. An undisturbed soil sample has a dry unit weight of 112 pcf with a specific gravity of solids equals to 2.68.
A 2.50-g sample of a large biomolecule was dissolved in 13.0 g of carbon tetrachloride. The boiling point of this solution was determined to be 77.85°C. Calculate the molar mass of the biomolecule.
Atrazine, a neutral triazine herbicide manufactured by the Ciba-Geigy group, undergoes biological and chemical decomposition to formhydroxy-atrazine. a).Assuming a pseudo first order decay constant of 0.01/day for atrazinr and 0.005/dayfor hydroxy..
The following wind conditions are expected: V = 10 i - 5 j mph for 0 10 hr. Draw to scale the expected streakline of the stream for t = 3, 10, and 15 hr.
Using the method of Lee et al., predict the temperature required in an isothermal plug flow incinerator to reduce the xylene level in a waste gas from 100 ppm to 10 ppm. Assume a residence time of 0.7 sec.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd