What distance will the shoreline recede if the lake shore

Assignment Help Civil Engineering
Reference no: EM13557107

Lake Pleasant, AZ, has a surface area of approximately 2,000 ha. The inflow for the month of August is zero. The lake is dammed so that no water leaves the impoundment downstream of the dam. There is no rain in August. The evaporation is estimated to be 6.8 mm/d. and the seepage is estimated to be 0.01 mm/d. Assuming that the lake shore is vertical, estimate the distance the lake elevation drops during the month of August. What distance will the shoreline recede if the lake shore slope is 5°?

Reference no: EM13557107

Questions Cloud

Calculate the active and passive pressures at the lower end : A line of sheet piling is driven 4m into a firm clay and retains, on one side, a 3m depth of fill on top of the clay. Water table level is at the surface of the clay. The unit weight of the fill is 18kN/m3 and the saturated unit weight of the clay is..
Determine the factor of safety with respect to shear failure : A footing 3m X 3m carries a pressure of 500 kN/ m2 at a depth of 1m in a sand substrate. The saturated unit weight of the sand is 20 kN/ m3 and the unit weight above the water table is 18 kN/ m3
What is the allowable slope angle if a factor of safety : A cutting 9 m deep is to be excavated in saturated clay of unit weight 19 kN/m3. The design shear strength parameters are cu = 30 kN/ m2 and u = 0. A hard stratum underlies the clay at a depth of 11 m below ground level.
What is the maximum torque so that the allowable shear : A hollow circular cylinder made of steel (E =200 GPa, G=77 GPa)is subject to a torque T at one end and is fixed at the other end outer diameter of the rod is 50mm and inner diameter is 44mm.
What distance will the shoreline recede if the lake shore : Lake Pleasant, AZ, has a surface area of approximately 2,000 ha. The inflow for the month of August is zero. The lake is dammed so that no water leaves the impoundment downstream of the dam
What is the maximum steady speed : A vehicle of mass 2000 kg coasts along a horizontal track against a drag force Fd (in N) on the automobile given by the following Fd=kV^2 where k= 1.25 kg/m and V is the speed in m/s
Convert the pressure to mm of blood assuming the specific : The sphygmomanometer is a device used to measure blood pressure. For a healthy person, the diastolic pressure is about 80mmHg (gage). Convert the pressure to mm of blood assuming the specific gravity of mercury and blood are 13.6 and 1.05, respective..
Determine the average density of the material form : The earth's interior comprises three principle regions: the Core (16.4% of the earth's total volume, density= 11.2 kg/L), the Mantle (82% fo the earth's total volume, density= 4.7 kg/L), and the crust (1.6% of the earth's volume
What is the probability that if you purchase the car : An automobile that you are looking at purchasing has an advertised fuel mileage of 30 miles per gallon. You rent the car for a week and track your mileage to school and back home and get (miles/gallon):

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the length of the crest required

1.An ungated spillway is to deliver 150,000 cfs with a crestelevation of 1000 ft. The upstream reservoir elevation is not toexceed the elevation of 1030 ft. The streambed is at elevation 800ft. Determine the length of the crest required.

  Determine the required pumping rate

Four pumps are to be used in 0.5-m diameter wells at the four corners of the site. Determine the required pumping rate. The aquifer has T = 1600 m^2/day and the wells each have a radius of influence of 600 m.

  Explain indicated concentrations of total volatile solids

Influent sample collected from a wastewater treatment plant was analyzed for various solids concentrations. Results indicated concentrations of Total Volatile Solids (TVS)

  How long will take until the height is 1 m above the orifice

A tank with a 3m diameter has an 8 cm orifice at the bottom. The tank is currently filled with water to a height of 2.5m above the orifice. If the orifice is opened, how long will it take until the height is 1 m.

  What are the efforts of work hardening of work materials

What are the effects of hardness, hot strength and hot hardness and work hardening of work materials

  How much does the aggregate in the wheelbarrow weight

you fill a 2-cubic foot wheelbarrow to the top with aggregate. if the specific gravity of the aggregate is 2.548 and 18% of the aggregate is void spaces, how much does the aggregate in the wheelbarrow weight?

  Compute the settlement resulting from primary consolidation

A 3-m-thick, wide fill (γ = 19 kN/m3) is placed over a soil profile consisting of 6 m of plastic clay (γ = 16 kN/m3, e0, = 1.7, Cc, = 1.2, OCR= 1.4, Cr/Cc, = 0.15) over 10 m of organic silt

  Find bottles contain tablets for thyroid

An overnight shipment contains 2 bottles of Aspirin and 3 bottles of thyroid tablets. A second shipment contains 3 bottle of aspirin, 2 bottles of thyroid and 1 bottle of laxative tablets. If one bottle is randomly chosen from each of the two shipmen..

  Determine the angle of internal friction for the soil

A cohesionless soil sample was subjected to a triaxial test. The sample failed when the minor principal stress (confining pressure) was 1200 lb/ft^2 and the deviator stress was 3000 lb/ft^2.

  How much energy in horsepower is lost by the water while

A pipeline 1200 ft long and 8 in. in diameter has at its inlet point 75ft of available hydraulic energy with respect to the reference level. The velocity in the pipe is 5 fps: the pressure at its end is 12psi.

  Determine the new value of l if the flowrate stayed the same

When a channel of triangular cross section was new, a flowrate of Q caused the water to reach L = 2 m up the side of the channel. After considerable use, the walls of the channel became rougher and the Manning coefficient, n, doubled.

  Determine torque that the titanium alloy shaft can transmit

Determine the torque that the Titanium Alloy shaft can transmit if the allowable angle of twist is 0.375 RAD. Assume the torque is applied at the end of the shaft. The shaft is 2 meters long and has a diameter of 25 mm.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd