What is the maximum steady speed

Assignment Help Civil Engineering
Reference no: EM13557106

A vehicle of mass 2000 kg coasts along a horizontal track against a drag force Fd (in N) on the automobile given by the following Fd=kV^2 where k= 1.25 kg/m and V is the speed in m/s. Assume the force that the engine must exert is equal to the drag force. The power exerted by the engine is 75hp. What is the maximum steady speed (in mph)?

Reference no: EM13557106

Questions Cloud

Determine the factor of safety with respect to shear failure : A footing 3m X 3m carries a pressure of 500 kN/ m2 at a depth of 1m in a sand substrate. The saturated unit weight of the sand is 20 kN/ m3 and the unit weight above the water table is 18 kN/ m3
What is the allowable slope angle if a factor of safety : A cutting 9 m deep is to be excavated in saturated clay of unit weight 19 kN/m3. The design shear strength parameters are cu = 30 kN/ m2 and u = 0. A hard stratum underlies the clay at a depth of 11 m below ground level.
What is the maximum torque so that the allowable shear : A hollow circular cylinder made of steel (E =200 GPa, G=77 GPa)is subject to a torque T at one end and is fixed at the other end outer diameter of the rod is 50mm and inner diameter is 44mm.
What distance will the shoreline recede if the lake shore : Lake Pleasant, AZ, has a surface area of approximately 2,000 ha. The inflow for the month of August is zero. The lake is dammed so that no water leaves the impoundment downstream of the dam
What is the maximum steady speed : A vehicle of mass 2000 kg coasts along a horizontal track against a drag force Fd (in N) on the automobile given by the following Fd=kV^2 where k= 1.25 kg/m and V is the speed in m/s
Convert the pressure to mm of blood assuming the specific : The sphygmomanometer is a device used to measure blood pressure. For a healthy person, the diastolic pressure is about 80mmHg (gage). Convert the pressure to mm of blood assuming the specific gravity of mercury and blood are 13.6 and 1.05, respective..
Determine the average density of the material form : The earth's interior comprises three principle regions: the Core (16.4% of the earth's total volume, density= 11.2 kg/L), the Mantle (82% fo the earth's total volume, density= 4.7 kg/L), and the crust (1.6% of the earth's volume
What is the probability that if you purchase the car : An automobile that you are looking at purchasing has an advertised fuel mileage of 30 miles per gallon. You rent the car for a week and track your mileage to school and back home and get (miles/gallon):
What is the work done by the wire : Water boils at room temperature of 25 degrees celsius when the pressure is 3.17 kPa (abs). Express this as a vaccum gage pressure (in mmHg) if atmospheric pressure is 101 kPa. Provide details of work to get a good rating.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the effectiveness of the regenerator

A Brayton cycle with a regenerator uses air as the working fluid. The air enters the compressor at 283K and 0.1 MPa. The highest temperature in the cycle is 1073K and the pressure ratio across the compressor is 8

  Calculate ultimate bod where discharge and river meet

Wastewater from a paper mill contains ultimate BOD of 200ppm and DO of 3ppm, water is discharged at a rate of 100,000 gallons per day into a river, the river has a flow of 1 million gallons per day with no BOD

  Design rectangular sections for beams-loads and values given

fy=50000psi, f'c=3000 span of l=28 ft, dead load not including beam weight = 3 k/ft, live load=3 k/ft, p*=0.5pb, concrete weights=150 lb/ft cubed, use h=d+2.5 inch, assume beam weight =10kN/m and phi=0.90

  Friction on the concrete surface creates a couple moment

Friction on the concrete surface creates a couple moment of 100 Mm on the blades of the trowel. Determines the magnitude of the resultant couple forces so that the resultant couple on the trowel is zero.

  Determine the expected drawdown in the pumping well

The drawdown in another observation well 60 m from the pumping well is 1.1 m. Calculate (a) the hydraulic conductivity of the aquifer, (b) the expected drawdown in the pumping well,

  Find the settling velocity of a 20 µm diameter particle with

Find the settling velocity of a 20 µm diameter particle with density 1500 kg/m3. If this particle had been hurled to a height of 8,000 m during a volcanic eruption, estimate the time required to reach the ground

  Which would be the strongest and highest bmelting point

explain how mechanical strength, melting temperature , and thermal exapntion are related at the atomic level. specifically, how do they relate to each other and the bonding energy between the atoms.

  Determine what is ph of the solution at equilibrium

Calcium sulfate (CaSO4, solubility product Ksp=2*10^-5 M^2), is added to initially pure water, such that solid CaSO4 remains at equilibrium. (Assume the sulfate does not participate in reaction other than the solubility product; no HSO4- formed).

  What would side slope of cut be if catch point is located

A backsight reading of 2.56 was obtained with rod at A and a foresight reading of 7.45 was obtained with the rod at the trial point B. If B is located 37.00 feet from the center line of a planned 50-foot wide road, is the catch point located uphi..

  Estimate the power required to accelerate a 1350 kg vehicle

The vehicle has a frontal cross -sectional area of 1.9 m^2. The roadway has a straight alignment and a badly patched and broken asphalt surface. assume a drag coefficient of 0.3 and p of air of 1.29 kg/m^3

  What load factor percent of seats occupied to break even

The carrier does not intend to offer weekend service. Therefore, the carrier will offer daily round-trip flights Monday through Friday. The following table presents passenger demand estimates and fares charged by competitors

  Provide a diagram showing the cost of the truss as function

A project for constructing a Facility just started. It involves the excavation of 40 to 60 feet deep and 60 feet wide trench to house double tunnels. A 24-inch outside diameter (22.5-inch inside diamater) water line is located in the path of the t..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd