Revolve the pavement about its inside edge

Assignment Help Civil Engineering
Reference no: EM13543445

Calculate the super-elevation required for a horizontal curve on a two-lane, two- way highway with 60 mph design speed, and a 1200 ft. radius curve. What is the required length of the spiral curve? If the lane width is 12 ft, and the cross (side) slope of the crown section is 2.0%, draw to a convenient scale the progress of pavement edges to attain the superelevation. Revolve the pavement about its

a. Inside edge. b. Outside edge c. Centerline

Reference no: EM13543445

Previous Q& A

  What should be the surface area of each tank

Do the problem again but for an alum or iron floc with an overflow rate 20 m3/day.m2?

  Determine the total work produced during this adiabatic

An adiabatic piston-cylinder device equipped with a spring maintains the pressure inside at at 300kPa when the volume is 0, and 3000kPa when the volume is 5 m3. The device is connected to a steam line maintained at 1500kPa and 200 C

  Determine the initial discharge velocity from the tank

Where z is the water height above the center of the valve. Determine (a) the initial discharge velocity from the tank and (b) the time required to empty the tank. The tank is considered to be empty when the water level drops to the center of the valv..

  Find the center of gravity of the given composite body

The tube supports the four parallel forces. Determine the magnitude of the forces and acting at C and D so that the equivalent resultant force of the four forces acts at point O.

  Will such a procedure produce a greater flowrate

A 12in diameter water main in your city has become very rough due to rust and corrosion, it has been suggested that the flowrate through the this pipe can be increased by inserting a smooth plastic liner into the pipe.

  How much time should each employee spend at each in order

To avoid boredom, employees are assigned all three tasks at different times during the shift. Each employee has to work at least half an hour at each station during a five hour shift. How much time should each employee spend at each in order to maxim..

  Provide the velocity distribution for steady flow case

An infinite, long, solid, vertical cylinder of radius R is located in infinite mass of compressible liquid. Provide the velocity distribution for steady flow case

  Determine the normal stress in each rod. show all work

Two steel rods with fixed supports at A and C are attached by a rigid flange at point B and a downward load of 120 kN is applied to the flange. The upper rod has a cross section of 800 mm^2 and the lower rod has

  Determine the minimum diameter shaft that can be used

The electric motor at A exerts a torque of 800N.m on the steel shaft from A to D. This has a torque of -300N.m at B and -500N.m at C. the dimensions are

  Why does a design engineer need to know the location of the

Course Ab of a five sided traverse runs due north. From the giben balanced interior angles to the right, compute and tabulate the bearings and azimuths from north for each side of the traverses.

Reviews

Write a Review

 

Similar Q& A

  Will the two drops collide

A carpenter uses a hammer to strike a nail. Approximate the hammer's weight of 1.8lbs, as being concentrated at the head, and assume that at impact the head is traveling in the -j direction

  How much error would there be in the volume calculation

Assume the actual water temperature for calibrating a 1/3 ft3 measure was 65 degrees F. If you had used a water temperature of 75 degrees F for your calibration, how much error would there be in your volume calculation (both in ft3 and as a percen..

  How much energy is used per mile of four different cars

We are analysing energy efficiency of four different cars, A (3.2 miles/kwh), B (42 mpg using Clean Diesel), C (22 mpg using corn based ethanol E85), and D (28 mpg using regular gasoline). Now accounting for all of the energy used, including extra..

  What is the rate of heat removal from the surroundings

Heat transfer through the walls and roof is estimated to be 5 40 kJ/hr per degree temperature difference between the inside and outside. a. If the outside temperature in the winter is - 5 C, what power required to drive the heat pum p (kJ/hr

  Determine the increment of vertical stress in the soil

Constructing the foundation causes changes in the levels of vertical stress at all points in the soil. One such point lies at the centre of the footing plan, and is at a depth of 10 m. Determine the increment of vertical stress there.

  Determine the components and magnitudes of the vectors ab

In order to move a wrecked truck, two cables are attached to the truck at A and pulled by winches B and C as shown. Determine the components and magnitudes of the vectors AB and AC

  Determine ratio for which material cost per pound of ethyle

Ethyl acetate is made from acetic acid and ethyl alcohol. Let x = pounds of acetic acid input, y=pounds of ethyl acohol input, and z = pounds of ethyl acetate output. The relationship of output to input is: z^2/(1.47x - z)(1.91y - z) = 3.9.

  Determine bearing stress in the soil including the weight

A concrete column with cross-sectional area is A= 120inches squared supports an axial compressive load P=9.0 kip, including the weight of the column. Determine the bearing stress in the soil. Concrete weighs 150lb/ft cubed

  Compute the magnitues of all the forces acting on member

Compute the magnitues of all the forces acting on member CDE of the frame. There are pins at C D and E and an 80 kelp force on the right. Length measurements are in ft.

  A symmetric compound channel in over bank flow has a main

a symmetric compound channel in over bank flow has a main channel with a bottom width of 30 m side slopes of 11 and a

  Find the final temperature using the three methods noted

It is desired to compare the results of property predictions for water near or in the saturation region using (a) the ideal gas equation, (b) the compressibility chart and (c) the steam tables.

  Whate are the relative fractions of ferrite and cementite

A Fe-.25 w/o Carbon alloy is sloly cooled to 700 degrees C. What is the composition of the Ferrite(alfa) phase and what is the compositon of the cementite(Fe3C) phase. Whate are the relative fractions of ferrite and cementite

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd