Find electric field of long line charge at radial distance

Assignment Help Electrical Engineering
Reference no: EM13252122

Find the electric field of a long line charge at a radial distance where the potential is 12V higher than at a radial distance
\(r_{1}=1m\)
where the magnitude of the electric field is 5V/m .

Reference no: EM13252122

Questions Cloud

What is the magnetic moment of the rotating ring : A uniform ring with a radius of 2.15 cm and a total charge of 6.37 ?C rotates with a constant angular speed of 3.84 rad/s, What is the magnetic moment of the rotating ring
Write a memo to board describing what actions must be taken : Write a memo to the Board describing what actions must be taken before the performance management program can be effectively implemented. Discuss the primary goal of each of these interventions and explain how you will know that these goals have b..
Active presentations with regards to health : Who is an example that does active Presentations with regards to Health? Like the Tony Robbins for Healthcare (particularly ergonomics, bodybuilding etc...)
Find the maximum radius for the curve : A car of mass 1200 kg turns a corner inclined at 55 deg at a speed of 20 m/s. What is the maximum radius for the curve at which the car will not slide down the incline
Find electric field of long line charge at radial distance : Find the electric field of a long line charge at a radial distance where the potential is 12V higher than at a radial distance  \(r_{1}=1m\) where the magnitude of the electric field is 5V/m .
Collected in a clinical trial evaluating : The following data were collected in a clinical trial evaluating a new compound designed to improve wound healing in trauma patients. The new compound is compared against a placebo.
Determine the magnitude of the emf induced in the loop : A circular wire loop, with a single turn, has a radius of 14.0 cm. The loop is in a magnetic field that is decreasing at the rate of 0.500 T/s. determine the magnitude of the emf induced in the loop
What is the cost to inspect each unit : A) What is the cost to inspect each unit? B) Is there benefit (or loss) from the current inspection process? How much?, Hourly, and Per Unit? C) Based on the above parts, what is your conclusion?
What is the utilization of the inspector : What is the average time that a vehicle musht wait to get through the system? C) What is the utilization of the inspector? D) What is the probability that when you arrive there will be three or more vehicle ahead of you?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What would be the current drawn by two bulbs

Consider the problem of using a low-voltage system to power a small cabin. Suppose a 12-V system powers a pair of 100-W lightbulbs (wired in parallel). a. What would be the (filament) resistance of a bulb designed to use 100 W when it receives 12 V

  What does transfer function of a filter represent

What does "transfer function" of a filter represent What do the Amplitude Ratio (Gain) and Phase Angle represent What are the key differences between a real filter (the RC circuit) and an Ideal Filter (please read LPF Treated as an Ideal Filter)

  Compute the period of transmission-time between bits

A WLAN uses the 1-Mbps IEEE 802.11 infrared standard and the 16-PPM modulation scheme. Compute the period of transmission (time between bits).

  Determine the efficiency of a high frequency induction

determine the efficiency of a high frequency induction furnace which takes 10 minutes to melt 1.815 kg of aluminium the input of the furnace being 5 KW and the initial temperature 15 deg.

  What are the advantages of digital communication over analog

Describe the phenomenon of aliasing caused by under sampling. How can aliasing be mitigated What are the advantages of digital communication over analog What is quantization noise How can you reduce it

  Design a multirange ammeter with ranges of 1-10ma

design a multirange ammeter with ranges of 1-10mA,0-100mA, and 0-1500mA, using a 5mA movement whose internal resistance is 3.8ohms. draw a circuit diagram of the meter.

  Calculate per-phase current that has to be carried by cables

It operates at a power factor of 0.85 (lagging) at its rated conditions. Calculate the per-phase current that has to be carried by the cables to the power electronics converter and the step-up transformer located at the base of the tower.

  Draw the gate-level diagram

Write the logic equation for Y in terms of A,B,C that solves this problem, and draw the gate-level diagram.

  State whether or not system is linear and time invariant

For each of the following systems with input x(t) and output y(t), state whether or not the system is (i) Linear and (ii) Time Invariant. Note that x(t) could be any complex valued signal.  (a) y(t) = a^2 x(t), where a is a complex number.

  Design a voltage-divider network to supply the load

The voltage across the load must remain between 4.7 and 5.0 V for all values of load current. Design a voltage-divider network to supply the load. You may assume that resistors of any value desired are available.

  . identify each system as either undamped or overdamped

The following 4 differential equations describe mass spring systems. Identify each system as either undamped, overdamped, underdamped, or critically damped (Justify your answer). Determine the angular frequency and period for the undamped

  Determine what should the address size be

If you have 16 kibibytes of memory plus a few (less than 10) memory mapped devices (assume that each device uses 16 bytes of address space), what should the address size be

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd